Sharp PG-D2510X appendix Turning the Projector On/Off, Power indicator Lamp indicator

Page 27

Turning the Projector On/Off

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 24.)

Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote control.

•The power indicator illuminates green.

•After the lamp indicator illuminates, the projector is ready to start operation.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight

ﬂ ickering of the image may be experienced within the ﬁ rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

•If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 50 for details.

Info

•When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 49.)

•English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 48.

Power indicator Lamp indicator

STANDBY/ON button

STANDBY button

ON button

On-screen display (conﬁrmation message)

Basic Operation

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the conﬁrmation message is displayed, to put the projector into Standby mode.

• The projector cannot be turned on while cooling.

Info

•Direct Power Off function:

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

25

Image 27

Contents PG-D2510X Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal For Future Reference Maintenance Troubleshooting IndexContents Reference Adjusting the Projector Function PRJ-ADJ1/2 MenuPower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Page Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals CLICK/EFFECT button 34 VOL +/- Volume buttonsBreak Timer button Picture Mode buttonRemote control signal transmitters Inserting the BatteriesUsable Range Easy Start Setup and ProjectionTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Screen Lens center Signal Input Normal ModeSignal Input 169 Mode Screen Size and Projection DistanceCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment RGB Connecting the Power Cord AC socket Power cord To AC outlet suppliedControlling the Projector by a Computer Power indicator Lamp indicator Turning the Projector On/OffTurning the Projector On Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screenMake small adjustments Height Adjust lever Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector levelPress Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionSwitching the Input Mode Adjusting the VolumeInput buttons AV Mute button VOL +/- Volume buttons Buttons Press Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingPicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press MenuFollowing items can be conﬁgured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete MenuImage while watching it To adjust the projectedPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the ColorsSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Signal Type SettingResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupKeystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image PositionFor Americas only Setting the OverscanSetting the On-screen Display Closed CaptionSelecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected ImagesAuto Restart Function Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker SettingEnter the same keycode in Re- conﬁrm Adjusting the Projector Function PRJ-ADJ1/2 MenuFan Mode Setting System Lock FunctionSelect On, then press Enter Keylock FunctionSelecting the Quick Start Menu COMPUTER2 SelectChecking the Lamp Life Status Setting the Function Button OperationStandby Mode Standby Audio OutCleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unitResetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin AssignmentsUSB Terminal Type B USB connector Basic format RS-232C Speciﬁcations and CommandsComputer control Communication conditionsProjector CommandsERR Video Video Input Picture Mode Standard OK or ERR Appendix CC1 Computer Compatibility Chart21-24 Troubleshooting53, 54 For Sharp Assistance Speciﬁcations Dimensions Index Kensington Security Standard connector ·················13