Sharp PG-D2510X appendix Resetting the Lamp Timer

Page 60

Regarding the Lamp (Continued)

4Remove the lamp unit.

•Loosen the securing screw from the lamp unit. Hold the lamp unit and pull it in the

	direction of the arrow. At this time, keep	Securing
	direction of the arrow. At this time, keep	screw
	the lamp unit horizontal and do not tilt it.	screw

5

6

Insert the new lamp unit.

•Press the lamp unit ﬁ rmly into the lamp unit compartment. Fasten the securing screw.

Replace the lamp unit cover.

•Align the tab on the lamp unit cover

(1) and close it (2). Then tighten the user service screw (3) to secure the lamp unit cover.

Info

•If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

1 Connect the power cord and open the lens shutter fully.

•Plug the power cord into the AC socket of the projector.

2 Reset the lamp timer.

•While simultaneously holding down MENU, ENTER and R on the projector, press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

AC socket

STANDBY/ON button

ENTER button

MENU button R button

58

Image 60

Contents PG-D2510X Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Maintenance Troubleshooting Index For Future ReferenceContents Adjusting the Projector Function PRJ-ADJ1/2 Menu ReferenceCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Page Accessories Optional accessoriesPart Names and Functions Front ViewRear View Terminals VOL +/- Volume buttons Break Timer buttonPicture Mode button CLICK/EFFECT button 34Remote control signal transmitters Inserting the BatteriesUsable Range Setup and Projection Easy StartTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Signal Input Normal Mode Signal Input 169 ModeScreen Size and Projection Distance Screen Lens centerProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment Terminals on the ProjectorConnecting the Projector to Other Equipment RGB Connecting the Power Cord AC socket Power cord To AC outlet suppliedControlling the Projector by a Computer Power indicator Lamp indicator Turning the Projector On/OffTurning the Projector On About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Make small adjustments Height Adjust leverPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press KeystoneSwitching the Input Mode Adjusting the VolumeInput buttons AV Mute button VOL +/- Volume buttons Buttons Resize Mode Press ResizeAbout Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageUsing the Remote Control as the Wireless Computer Mouse When moving the cursorWhen left-clicking When right-clickingMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start MenuTo adjust the projected Image while watching itPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Signal Type SettingResolution Setting Setting the Video Setup When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Auto Restart FunctionAdjusting the Projector Function PRJ-ADJ1/2 Menu Fan Mode SettingSystem Lock Function Enter the same keycode in Re- conﬁrmKeylock Function Selecting the Quick Start MenuCOMPUTER2 Select Select On, then press EnterSetting the Function Button Operation Standby ModeStandby Audio Out Checking the Lamp Life StatusMaintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Remove the lamp unit coverLamp unit STANDBY/ON button AC socketResetting the Lamp Timer Connecting Pin Assignments COMPUTER/COMPONENT input and COMPUTER/COMPONENT outputUSB Terminal Type B USB connector RS-232C Speciﬁcations and Commands Computer controlCommunication conditions Basic formatCommands ProjectorERR Video Video Input Picture Mode Standard OK or ERR Appendix CC1 Compatibility Chart ComputerTroubleshooting 21-2453, 54 For Sharp Assistance Speciﬁcations Dimensions Kensington Security Standard connector ·················13 Index