Sharp PG-D2510X appendix Information Product Disposal

Page 4
U.S.A. ONLY
U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.

Caution Concerning Lamp Replacement

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Caution

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

■Carefully change the lamp by following the instructions described on pages 56 to 58.

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

2

Page 3 Page 5
Image 4
Page 3 Page 5
Contents PG-D2510X Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Maintenance Troubleshooting Index For Future ReferenceContents Adjusting the Projector Function PRJ-ADJ1/2 Menu ReferenceCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Page Accessories Optional accessoriesPart Names and Functions Front ViewRear View Terminals VOL +/- Volume buttons Break Timer buttonPicture Mode button CLICK/EFFECT button 34Inserting the Batteries Remote control signal transmittersUsable Range Setup and Projection Easy StartTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Signal Input Normal Mode Signal Input 169 ModeScreen Size and Projection Distance Screen Lens centerProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment Terminals on the ProjectorConnecting the Projector to Other Equipment RGB AC socket Power cord To AC outlet supplied Connecting the Power CordControlling the Projector by a Computer Turning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Make small adjustments Height Adjust leverPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeInput buttons AV Mute button VOL +/- Volume buttons Buttons Resize Mode Press ResizeAbout Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageUsing the Remote Control as the Wireless Computer Mouse When moving the cursorWhen left-clicking When right-clickingMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be configured on the Quick Start MenuTo adjust the projected Image while watching itSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting Setting the Video Setup When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Auto Restart FunctionAdjusting the Projector Function PRJ-ADJ1/2 Menu Fan Mode SettingSystem Lock Function Enter the same keycode in Re- confirmKeylock Function Selecting the Quick Start MenuCOMPUTER2 Select Select On, then press EnterSetting the Function Button Operation Standby ModeStandby Audio Out Checking the Lamp Life StatusMaintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Removing and Installing the Lamp Unit Remove the lamp unit coverLamp unit STANDBY/ON button AC socketResetting the Lamp Timer Connecting Pin Assignments COMPUTER/COMPONENT input and COMPUTER/COMPONENT outputUSB Terminal Type B USB connector RS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands ProjectorERR Video Video Input Picture Mode Standard OK or ERR Appendix CC1 Compatibility Chart ComputerTroubleshooting 21-2453, 54 For Sharp Assistance Specifications Dimensions Kensington Security Standard connector ·················13 Index
Top Page Image Contents