Sharp PG-D2510X Removing and Installing the Lamp Unit, Remove the lamp unit cover, Lamp unit

Page 59

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-D350LP
	AN-D350LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Close the lens shutter and turn the

projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

Appendix

57

Image 59

Contents PG-D2510X Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal For Future Reference Maintenance Troubleshooting IndexContents Reference Adjusting the Projector Function PRJ-ADJ1/2 MenuPower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Page Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals CLICK/EFFECT button 34 VOL +/- Volume buttonsBreak Timer button Picture Mode buttonUsable Range Remote control signal transmittersInserting the Batteries Easy Start Setup and ProjectionTurn the computer on Turn the power off Standard Setup Front Projection Setting Up the ProjectorSetting Up the Projector Screen Lens center Signal Input Normal ModeSignal Input 169 Mode Screen Size and Projection DistanceCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment RGB Controlling the Projector by a Computer Connecting the Power CordAC socket Power cord To AC outlet supplied Turning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screenMake small adjustments Height Adjust lever Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector levelPress Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionInput buttons AV Mute button VOL +/- Volume buttons Buttons Switching the Input ModeAdjusting the Volume Press Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingPicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press MenuFollowing items can be conﬁgured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete MenuImage while watching it To adjust the projectedMenu operation n Picture Adjustment Picture MenuSelecting the Picture Mode Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the ColorsReducing Image Noise DNR Selecting the Film ModeEco+Quiet Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupKeystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image PositionFor Americas only Setting the OverscanSetting the On-screen Display Closed CaptionSelecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected ImagesAuto Restart Function Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker SettingEnter the same keycode in Re- conﬁrm Adjusting the Projector Function PRJ-ADJ1/2 MenuFan Mode Setting System Lock FunctionSelect On, then press Enter Keylock FunctionSelecting the Quick Start Menu COMPUTER2 SelectChecking the Lamp Life Status Setting the Function Button OperationStandby Mode Standby Audio OutCleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unitResetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin AssignmentsUSB Terminal Type B USB connector Basic format RS-232C Speciﬁcations and CommandsComputer control Communication conditionsProjector CommandsERR Video Video Input Picture Mode Standard OK or ERR Appendix CC1 Computer Compatibility Chart21-24 Troubleshooting53, 54 For Sharp Assistance Speciﬁcations Dimensions Index Kensington Security Standard connector ·················13