Sharp PG-D2510X See bottom of projector, Void the users authority to operate this equipment

Page 3
U.S.A. ONLY
U.S.A. ONLY

Before using the projector, please read this operation manual carefully.

IntroductionENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1.WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2.CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notifi cation of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fi re or electric shock, do not expose this product to rain or moisture.

See bottom of projector.

The lightning fl ash with arrowhead sym-

CAUTION

bol, within an equilateral triangle, is in-

tended to alert the user to the presence

RISK OF ELECTRIC SHOCK.

of uninsulated “dangerous voltage”

DO NOT REMOVE SCREWS

within the product's enclosure that may

EXCEPT SPECIFIED USER

be of suffi cient magnitude to constitute

SERVICE SCREW.

a risk or electric shock to persons.

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

The exclamation point within a triangle

DO NOT REMOVE COVER.

is intended to alert the user to the pres-

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

ence of important operating and main-

REFER SERVICING TO QUALIFIED SERVICE

tenance (servicing) instructions in the

PERSONNEL.

literature accompanying the product.

 

WARNING:

 

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING: FCC Regulations state that any unauthorized changes or modifi cations to this equipment not expressly approved by the manufacturer could

void the user's authority to operate this equipment.

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verifi cation.

U.S.A. ONLY

Introduction

1

Image 3
Contents PG-D2510X Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal For Future Reference Maintenance Troubleshooting IndexContents Reference Adjusting the Projector Function PRJ-ADJ1/2 MenuPower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Page Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals CLICK/EFFECT button 34 VOL +/- Volume buttonsBreak Timer button Picture Mode buttonRemote control signal transmitters Inserting the BatteriesUsable Range Easy Start Setup and ProjectionTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Screen Lens center Signal Input Normal ModeSignal Input 169 Mode Screen Size and Projection DistanceCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment RGB Connecting the Power Cord AC socket Power cord To AC outlet suppliedControlling the Projector by a Computer Power indicator Lamp indicator Turning the Projector On/OffTurning the Projector On Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screenMake small adjustments Height Adjust lever Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector levelPress Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionSwitching the Input Mode Adjusting the VolumeInput buttons AV Mute button VOL +/- Volume buttons Buttons Press Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingPicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press MenuFollowing items can be configured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete MenuImage while watching it To adjust the projectedPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the ColorsSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Signal Type SettingResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupKeystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image PositionFor Americas only Setting the OverscanSetting the On-screen Display Closed CaptionSelecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected ImagesAuto Restart Function Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker SettingEnter the same keycode in Re- confirm Adjusting the Projector Function PRJ-ADJ1/2 MenuFan Mode Setting System Lock FunctionSelect On, then press Enter Keylock FunctionSelecting the Quick Start Menu COMPUTER2 SelectChecking the Lamp Life Status Setting the Function Button OperationStandby Mode Standby Audio OutCleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unitResetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin AssignmentsUSB Terminal Type B USB connector Basic format RS-232C Specifications and CommandsComputer control Communication conditionsProjector CommandsERR Video Video Input Picture Mode Standard OK or ERR Appendix CC1 Computer Compatibility Chart21-24 Troubleshooting53, 54 For Sharp Assistance Specifications Dimensions Index Kensington Security Standard connector ·················13