AMD GA-K8N51GMF-9 user manual Use of licensed Award Bios

Page 11

I/O Control

Š

Winbond W83627

Hardware Monitor

Š

System voltage detection

 

Š CPU / System temperature detection

 

Š CPU / System fan speed detection

 

Š

CPU warning temperature

 

Š CPU / System fan failure warning

 

Š CPU smart fan control(Note 2)

Onboard SATA

Š

Onboard nVIDIA® nForce 430 controller

3Gb/s RAID

 

- supports data striping (RAID 0), mirroring (RAID 1), RAID0+1,

 

 

and RAID 5 functions

 

 

- supports data transfer rate of up to 300 MB/s

 

 

- supports hot plugging function

 

 

- supports a maximum of 4 SATA 3Gb/s connections

 

 

- supported on the Win 2000/XP operating systems

BIOS

Š

Use of licensed AWARD BIOS

 

Š

Supports Q-Flash

Additional Features

Š

Supports @BIOS

 

Š Supports EasyTune (only supports Hardware Monitor function)(Note 3)

Overclocking

Š

Over Clock via BIOS (CPU/PCIE)

Form Factor

Š

Micro ATX form factor; 24.4cm x 24.4cm

English

(Note 2) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install. For more detailed information please check at the FAQ section on GIGABYTE's website.

(Note 3) EasyTune functions may vary depending on different motherboards.

- 11 -

Hardware Installation

Image 11
Contents GA-K8N51GMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8N51GMF-GA GA-K8N51GMF-9 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyALC880 Codec Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE ConnectorFaudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector13 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1g „ Exit Without Saving „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime Memory Floppy 3 Mode Support for Japan AreaDrive a Halt onBoot Up Floppy Seek Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceInit Display First Password CheckSPP Integrated PeripheralsOn-Chip IDE Channel1 SATA-II 2 Primary RAIDSATA-II 2 Secondary RAID On-Chip IDE Channel0Onboard 1394 Function Onboard LAN Boot ROMParallel Port Mode Onboard LAN FunctionModem Ring On Power Management SetupPower-On by Alarm PME Event Wake UpAC Back Function Power On By KeyboardKB Power on Password Power On By MousePCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status K8 CPU Clock Ratio Frequency/Voltage ControlCPU Frequency Pcie ClockLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English Taiwan Headquarters Contact UsChina Shanghai