AMD GA-K8N51GMF-9 SATA-II 2 Primary RAID, SATA-II 2 Secondary RAID, On-Chip IDE Channel0

Page 37

SATA-II 2 Primary RAID

Enabled	Enable SATAII 2 1st SATA RAID function.
Disabled	Disable this function. (Default value)

SATA-II 2 Secondary RAID

Enabled	Enable SATAII 2 2nd SATA RAID function.
Disabled	Disable this function. (Default value)

On-Chip IDE Channel0

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

On-Chip IDE Channel1

Enabled	Enable onboard 2nd channel IDE port. (Default value)
Disabled	Disable onboard 2nd channel IDE port.

IDE1 Conductor Cable

Auto BIOS autodetects IDE1 conductor cable. (Default Value)

ATA66/100/133 Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your IDE

	device and cable are compatible with ATA66/100/133).
ATA33	Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE device
	and cable are compatible with ATA33)

IDE2 Conductor Cable

Auto BIOS autodetects IDE2 conductor cable. (Default Value)

ATA66/100/133 Set IDE2 Conductor Cable to ATA66/100/133. (Please make sure your IDE

	device and cable are compatible with ATA66/100/133)
ATA33	Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE device
	and cable are compatible with ATA33)

Serial-ATA-II 1

Enabled	Enable Serial-ATAII 1 support. (Default Value)
Disabled	Disable Serial-ATAII 1 support.

Serial-ATA-II 2

Enabled	Enable Serial-ATAII 2 support. (Default Value)
Disabled	Disable Serial-ATAII 2 support.

On-Chip USB

V1.1+V2.0	Enable USB 1.1 and USB 2.0 controllers. (Default Value)
V1.1	Enable only USB 1.1 controller
Disabled	Disable onchip USB support.

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)

Onboard Audio Function

Auto	Auto-detect onboard audio function. (Default value)
Disabled	Disable this function.

	- 37 -	BIOS Setup

English

Image 37

Contents GA-K8N51GMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8N51GMF-GA GA-K8N51GMF-9 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerALC880 Codec Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE ConnectorFaudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector13 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1g „ Set User Password „ Set Supervisor Password„ Save & Exit Setup „ Exit Without SavingTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Password CheckSPP Integrated PeripheralsSATA-II 2 Secondary RAID SATA-II 2 Primary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Parallel Port Mode Onboard LAN Boot ROMOnboard LAN Function Onboard 1394 FunctionPower-On by Alarm Power Management SetupPME Event Wake Up Modem Ring OnKB Power on Password Power On By KeyboardPower On By Mouse AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Frequency Frequency/Voltage ControlPcie Clock K8 CPU Clock RatioLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosSelecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English Taiwan Headquarters Contact UsChina Shanghai