AMD GA-K8N51GMF-9 user manual Installing the RAID drivers, Cd bootdrv Menu

Page 69

Installing the RAID drivers

To install operating system onto a serial ATA hard disk successfully, you need to install the SATA controller driver during OS installation. Without the driver, the hard disk may not be recognized during the Windows setup process. First of all, copy the driver for the SATA controller from the motherboard driver CD-ROM to a floppy disk. See the instructions below about how to copy the driver in MS-DOS mode(Note). Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk.

Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from the

startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\> prompt, type the following two commands. Press ENTER after each command (Fig.1):

cd bootdrv

menu

Step 2: When the controller menu (Fig.2) appears, remove the startup disk and insert the blank formatted disk. Select the controller driver by pressing the corresponding letter from the menu. Your system will then automatically zip and transfer this driver file to the floppy disk. Press 0 to exit when finished.

English

Fig.2

Fig.1

Step 3: After completing the steps, boot from the Windows installation disk to install the RAID drivers. Press F6 as soon as you see the "Press F6 if you need to install a third party SCSI or RAID driver" message, then supply serial ATA controller driver by this floppy disk. Follow the on-screen instructions to complete the installation.

(Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under Windows once for that hard drive. After that, the driver will not have to be installed.)

(Note): For users without a startup disk.

Use an alternative system and insert the GIGABYTE motherboard driver CD-ROM. From the CD-ROM drive (example: D:\) double click the MENU.exe file in the BootDrv folder. A command prompt window will open similar to that in Fig. 2.

- 69 -

Appendix

Image 69
Contents GA-K8N51GMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8N51GMF-GA GA-K8N51GMF-9 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerALC880 Codec Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE ConnectorFaudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector13 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1g „ Set User Password „ Set Supervisor Password„ Save & Exit Setup „ Exit Without SavingStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Password CheckSPP Integrated PeripheralsSATA-II 2 Secondary RAID SATA-II 2 Primary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Parallel Port Mode Onboard LAN Boot ROMOnboard LAN Function Onboard 1394 FunctionPower-On by Alarm Power Management SetupPME Event Wake Up Modem Ring OnKB Power on Password Power On By KeyboardPower On By Mouse AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Frequency Frequency/Voltage ControlPcie Clock K8 CPU Clock RatioLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosSelecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English Taiwan Headquarters Contact UsChina Shanghai