AMD GA-K8N51GMF-9 user manual Faudio Front Audio Connector

Page 22

English

8)F_AUDIO (Front Audio Connector)

This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish to use the front audio function, connect the front panel audio module to this connector. Check the pin assignments carefully while you connect the front panel audio module. Incorrect connection between the module and connector will make the audio device unable to work or even damage it. For optional front panel audio module, please contact your chassis manufacturer.

10 9

2 1

HD Audio:

Pin No.

Definition

1

MIC2_L

2

GND

3

MIC2_R

4

-ACZ_DET

5

Line2_R

6

FSENSE1

7

FAUOIO_JD

8

No Pin

9

LINE2_L

10

FSENSE2

AC'97 Audio:

Pin No.

Definition

1

MIC

 

2

GND

 

3

MIC Power

 

4

NC

 

5

Line Out (R)

 

6

NC

 

7

NC

 

8

No Pin

 

9

Line Out (L)

 

10

NC

 

By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel audio module to this connector, please refer to the instructions on Page 74 about the software settings.

GA-K8N51GMF-9 Motherboard

- 22 -

Image 22
Contents GA-K8N51GMF-9 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8N51GMF-9 Motherboard Layout K8N51GMF-GABlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary ALC880 CodecUse of licensed Award Bios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceFaudio Front Audio Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2 Front USB Connector 13 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F1g „ Save & Exit Setup „ Set Supervisor Password„ Set User Password „ Exit Without SavingTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekPassword Check Init Display FirstIntegrated Peripherals SPPOn-Chip IDE Channel0 SATA-II 2 Primary RAIDSATA-II 2 Secondary RAID On-Chip IDE Channel1Onboard LAN Function Onboard LAN Boot ROMParallel Port Mode Onboard 1394 FunctionPME Event Wake Up Power Management SetupPower-On by Alarm Modem Ring OnPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Pcie Clock Frequency/Voltage ControlCPU Frequency K8 CPU Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen Task menu for Q-FlashTMutility FlashTMutility barCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish Appendix English Contact Us Taiwan HeadquartersChina Shanghai