AMD GA-K8N51GMF-9 Power Management Setup, PME Event Wake Up, Modem Ring On, Power-On by Alarm

Page 39

2-4

Power Management Setup

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

Power Management Setup

 

 

 

ACPI Suspend Type

[S1(POS)]

 

Item Help

 

Soft-Off by Power button

[Instant-Off]

Menu Level`

 

PME Event Wake Up

[Enabled]

 

 

 

 

Modem Ring On

[Enabled]

 

 

 

 

USB Resume from Suspend

[Enabled]

 

 

 

 

Power-On by Alarm

[Disabled]

 

 

 

x Day of Month Alarm

Everyday

 

 

 

x

Time (hh:mm:ss) Alarm

0 : 0 : 0

 

 

 

 

Power On By Keyboard

[Disabled]

 

 

 

x KB Power ON Password

Enter

 

 

 

 

Power On By Mouse

[Disabled]

 

 

 

 

AC BACK Function

[Soft-Off]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

ACPI Suspend Type

 

 

 

 

 

S1(POS)

Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)

 

S3(STR)

Set ACPI suspend type to S3/STR(Suspend To RAM).

 

 

Soft-Off by Power button

 

 

 

 

 

Instant-Off

Press power button then Power off instantly. (Default value)

 

 

Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed

 

 

less than 4 sec.

 

 

 

PME Event Wake Up

This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.

Disabled

Disable this function.

Enabled

Enable PME as wake up event. (Default value)

Modem Ring On

An incoming call via modem can awake the system from any suspend state.

Disabled

Disable this function.

Enabled

Enable Modem Ring On function. (Default value)

USB Resume from Suspend

Disabled

Disable this function.

Enable

Enable USB device wake up system from suspend mode. (Default value)

Power-On by Alarm

You can set "Power-On by Alarm" item to enabled and key in Date/Time to power on system.

Disabled

Disable this function. (Default value)

Enabled

Enable alarm function to POWER ON system.

If Power-On by Alarm is Enabled.

Day of Month Alarm :

Everyday, 1~31

Time (hh: mm: ss) Alarm :

(0~23) : (0~59) : (0~59)

English

- 39 -

BIOS Setup

Image 39
Contents GA-K8N51GMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8N51GMF-GA GA-K8N51GMF-9 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyALC880 Codec Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE ConnectorFaudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector13 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1g „ Exit Without Saving „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Memory Floppy 3 Mode Support for Japan AreaDrive a Halt onBoot Up Floppy Seek Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceInit Display First Password Check SPP Integrated PeripheralsOn-Chip IDE Channel1 SATA-II 2 Primary RAIDSATA-II 2 Secondary RAID On-Chip IDE Channel0Onboard 1394 Function Onboard LAN Boot ROMParallel Port Mode Onboard LAN FunctionModem Ring On Power Management SetupPower-On by Alarm PME Event Wake UpAC Back Function Power On By KeyboardKB Power on Password Power On By MousePCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status K8 CPU Clock Ratio Frequency/Voltage ControlCPU Frequency Pcie ClockLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English Taiwan Headquarters Contact UsChina Shanghai