AMD GA-K8N51GMF-9 Drive a, Floppy 3 Mode Support for Japan Area, Halt on, Base Memory

Page 33

Access Mode

Use this to set the access mode for the hard drive. The two options are:

 

Large/Auto(default:Auto)

Capacity

Capacity of currently installed hard drive.

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.

Cylinder

Number of cylinders

Head

Number of heads

Precomp

Write precomp

Landing Zone

Landing zone

Sector

Number of sectors

Drive A

The category identifies the types of floppy disk drive A that has been installed in the computer.

None

No floppy drive installed.

 

360K, 5.25"

5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25"

5.25 inch AT-type high-density drive; 1.2M byte capacity.

 

(3.5 inch when 3 Mode is Enabled).

 

720K, 3.5"

3.5

inch double-sided drive; 720K byte capacity

.

1.44M, 3.5"

3.5

inch double-sided drive; 1.44M byte capacity.

 

2.88M, 3.5"

3.5

inch double-sided drive; 2.88M byte capacity.

 

Floppy 3 Mode Support (for Japan Area)

 

Disabled

Normal Floppy Drive. (Default value)

 

Drive A

Drive A is 3 mode Floppy Drive.

 

Halt on

The category determines whether the computer will stop if an error is detected during power up.

No Errors

The system boot will not stop for any error that may be detected and you

 

will be prompted.

All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard

The system boot will not stop for a keyboard error; it will stop for all other

 

errors. (Default value)

All, But Diskette

The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all

 

other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

Total Memory

This item displays the memory size that used.

English

- 33 -

BIOS Setup

Image 33
Contents GA-K8N51GMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8N51GMF-GA GA-K8N51GMF-9 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerALC880 Codec Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE ConnectorFaudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector13 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1g „ Set User Password „ Set Supervisor Password„ Save & Exit Setup „ Exit Without SavingStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Password CheckSPP Integrated PeripheralsSATA-II 2 Secondary RAID SATA-II 2 Primary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Parallel Port Mode Onboard LAN Boot ROMOnboard LAN Function Onboard 1394 FunctionPower-On by Alarm Power Management SetupPME Event Wake Up Modem Ring OnKB Power on Password Power On By KeyboardPower On By Mouse AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Frequency Frequency/Voltage ControlPcie Clock K8 CPU Clock RatioLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosSelecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes TroubleshootingEnglish Appendix English Taiwan Headquarters Contact UsChina Shanghai