AMD GA-K8N51GMF-9 user manual Cdin CD In Connector, Pwrled

Page 24

English

10)CD_IN (CD In Connector)

Connect CD-ROM or DVD-ROM audio out to the connector.

			Pin No.	Definition
	1		1	CD-L
			2	GND
			2	GND
			3	GND
			4	CD-R

11)PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

	Pin No.	Definition
	1	MPD+
1	2	MPD-
	3	MPD-

GA-K8N51GMF-9 Motherboard

- 24 -

Image 24

Contents GA-K8N51GMF-9 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8N51GMF-9 Motherboard Layout K8N51GMF-GABlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary ALC880 CodecUse of licensed Award Bios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceFaudio Front Audio Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2 Front USB Connector 13 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F1g „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Floppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstIntegrated Peripherals SPPSATA-II 2 Primary RAID SATA-II 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Onboard LAN Boot ROM Parallel Port ModeOnboard LAN Function Onboard 1394 FunctionPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Keyboard KB Power on PasswordPower On By Mouse AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency/Voltage Control CPU FrequencyPcie Clock K8 CPU Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen Task menu for Q-FlashTMutility FlashTMutility barCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish Appendix English Contact Us Taiwan HeadquartersChina Shanghai