DreamGEAR MSK 33 manual Downloading New MSK33 Operating Software, General notes

Page 113

Downloading New MSK33 Operating Software

General notes:

Observe the bold lines. The non-bold notes can only help you solve a problem in cases of error. <RET> means to trigger the command with RETURN on the termi- nal programme.

1.Copy the file „MSK33.BXX“ (XX stands for the version number) from the diskette into an easily found directory of your hard disk.

2.Connect the MSK33 with the PC via a zero modem cable (see respective section). Set the baud rate to 19200 baud in the MODEM menu (SETTING / MODEM). Note down the PIN (If no entry is available, PIN1 is <RET>).

If problems occur when using a 9-pin serial interface, the hardware handshake (r/cst) can be set to OF in the MODEM menu.

3.Switch off the MSK33, and press down any number key on the MSK 33. Start a terminal programme (we recommend Term95 in DOS mode) on the PC => MSK33 switches on.

For switched of hardware handshake, the MSK 33 must be switched on by hand.

Note: When using the terminal programme, Hyperterminal, under Windows95, we recommend to use the fonts TERMINAL STANDARD 14 and OEM/DOS. Set emulation to automatic recognition or ANSI.

4.the MSK 33 answers now with the bootloader „MSKUL>„. Enter in PIN1 and confirm the entry with <RET> (Standard PIN1 is-MSK-33-).

For switched off handshake, the MSK 33 first answers after entry of <RET>. If the MSK 33 answer with „MSK 33>„ instead of „MSKUL>„, it must have been changed in the upload operating with the command, UPL<RET>.

Note: With the command, LAN<RET>, you can change the language.

5.With the command UNL<RET>, the FLASH is released for programming. Afterwards switch the MSK 33 to reception with the command, BIN<RET>.

If the message is given from the MSK 33, that the access is refused, you may have tried to log-in with PIN2 or PIN3. In this case, start over with step 1.

6.Now, start the upload of the file „MSK33.BIN“ on the terminal programme. This occurs in the XMODEM mode (at 19200 baud ca. 3 minutes). ATTENTION: Of the upload is not started within a certain period of time, the MSK 33 locks up. In this case, you must start new from step 5 (command UNL, BIN).

7.After the upload, the uninterrupted transmission is confirmed by the MSK 33.

In the RAW-mode, the message is given after the successful download, that 232144 characters were downloaded.

8.Ext the terminal programme, switch off the MSK 33, switch on the MSK 33 on again without terminal programme and set fact.setup in the menu,

SETTING / SYSTEM.

113

Page 112 Page 114
Image 113
Page 112 Page 114
Contents Operating manual Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107Explanation of symbols General safety informationImportant Notes Validity of this manualConnections Safety InstructionsProper use Mechanical loadbearing capacityFunctions FunctionsFunction Functions overviewReturn path LP DVB-S DVB-S/C/TFront panel Displays, Operating Elements and ConnectionsRear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUXSide view MSK Observing angle of the on screen displayFrequently recurring softkeys Operating ConceptScreen Menu selection General information for operationMain menu Accu CAP % I=0.00 aMains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuseDC socket option Accumulator and Battery OperationAccumulator operation Connections Maximal input level Measurement PossibilitiesLevel measurement Sat menu Sat OperationEntering the transponder frequency Setting of the LNB voltage supplySelecting the LO frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROLLNB control menu KHz control signalLNB supply voltage LNB current drawDiSEqC Checking the LNB supply voltage of a satellite receiverCalling up the DiSEqC/V SEC menu DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field BData burst Tone burst Example Entering and transmitting a DiSEqC commandSimple DiSEqC General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 101390 Tx+rx CommandOperating the menus ModusSat Operation Entering the hex numbers Sending a V-SEC command TXSEC menu Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier MenuVideo polarity Second Anlaog menuSetting of the de-emphasis Audio carrier settingSat subcarrier menu Selecting the subcarrier recepAudio carrier table for reception type Audio carrier tables for the satellite reception27.500 SR Digital MeasurementsSAT Digital menu Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chanLNB U= 0.0 V I= 0 mA TV control menuTV-DiSEqC /VSEC menu Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriersMeasuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacingMode TV Digital menuSelecting demodulation for DVB-C measurement Selecting channel bandwidths DVB-T optionalReturn path if menu Return Path if MenuAudio carrier table for if reception Analog menuMeasurement of the current level Measurement of the min./max. levelMeasurement of the audio carrier spacing If RP Digital Menu QAM64 modeEntering symbol rate Radio Analog menu Radio OperationRadio menu Measuring the min/max level FM Measure ALLDecoder operation AV MenuDecoder operation baseband Video input Video outputMpeg transport stream interface TS-Parallel, Lvds optional Breaking voltageRGB operation 3sat KiKa Phoenix Mpeg Decoder Menu OptionalPAT 08 Offset 0.0 dB Setting MenuUnit Screen Menu Screen setupSetting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menuSaving the unit settings Saving and calling up unit settingsCalling up saved settings Copy MenuPrinting out all measurements in Sat mode Printing out all measurements in TV modeSpectr Mode MenuEnlarging the videotext Text MenuHolding the videotext Original videotext sizeHorizontal zoom Reducing the video signal Horizontal zoom -Enlarging the video signalScope Menu Video scope menuSelecting the video line Measurement of the amplitude of the video signalMeasurement of video signals via the AV socket Scart Pos Audio ScopeTime DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot ContMarker Span Spectral MenuMark AnaMarker dig Marker anaCross-polarisation measurement on signals in SAT operation Measurement of digital signals in Sat operationZoom marker Max offMeasurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairsFrontend locked Measurement of signal noise ratio SNRCarrier offset Selecting the code rate Selecting the symbol rate symbol-clockInverting /not inverting a constellation diagram Examples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-CZoom Inverting /not inverting constellation diagramExamples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier modeHierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSKTrack MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33Cable system With return path capable amplifiers Display of the check point Auto MeasureConnection cable for modem / RS InterfacesModem / RS 232 interface Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menuTTY mode Code PasswordAnsi mode Log-in procedureRequesting help Example for logging-in in Ansi modeInterfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDUMaintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbonCommand overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical AppendixReset Reset DiSEqC minicontroller Command overview command byteCommand overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXRChannel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESBVHF UHF Channel and frequency table standard Lfrequency in MHzVII Channel and frequency table standard D/K frequency in MHzViii XIIChannel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Power supply Technical DataTechnical data MER SNRQpsk BER Assignment of the Scart socket AccessoriesScope of delivery TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socketAssignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software9986498/0206 ZWT Subject to alterations
Top Page Image Contents