DreamGEAR MSK 33 manual Return Path if Menu, Return path if menu

Page 49

Return Path IF Menu

Return path IF menu

 

70

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

 

TV-IF38.90MHz A65.0dBµV

 

70

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

RP 22.40 MHz A

65.0dBµV

ANALOG Menu

BACK

IF CONTROL

analog

>

IF MEASURE

BACK

RP frq

RP-inv off

RP CONTROL digit. DVB-C>

RP MEASURE

In this menu, the video carriers -each according to optional assignment- can be measured on IF levels (38.9 MHz analogue and 36.15 MHz digital) or on the entire return path area (Optional return path card) from 4 MHz to 80 MHz.

Each according to assignment, the MSK 33 answers with the IF menu or the optional return path menu (refer to star marking).

Entering a frequency of 7.00 MHz up to 80.00MHz*

￿￿RP frq

The return path frequency can be entered in with the numerical button, „0...9,“ with the cursor buttons, ◄►, in 50 kHz increments. The frequency is displayed in the lower left-hand corner.

Inverting the RF spectrum*

RF-inv off ￿

By pressing this button, he RF spectrum can be inverted. This mean, that the video and audio carrier for digital modulation, the I and Q vectors can be exchanged.

analog

>

DIGITAL menu

digit. DVB-C>

RP MEASURE

RP MEASURE

Access the analogue menu with the buttons, “analog” and “RP MEAS- URE.” In this menu, settings and measurements of analogue signal are possible (For further information, refer to the TV Analog menu).

Access the digital menu with the buttons, “digit. DVB-C” and “RP MEASURE”. In this menu, settings and measurements of the DVB-C signals are possible. IF demodulation if DVB-T signals is also possible (For further information, refer to the TV digital menu).

IF CONTROL menu (RP-CONTROL*)

IF (RP)

CONTROL

In this menu, all remotely controlled parameters, such as remote feeding voltage, 22 kHz, DiSEqC, tone burst (simple DiSEqC), V-SEC, can be set (for further infor- mation, refer to TV menu).

49

Image 49
Contents Operating manual Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107Explanation of symbols General safety informationImportant Notes Validity of this manualConnections Safety InstructionsProper use Mechanical loadbearing capacityFunctions FunctionsFunction Functions overviewReturn path LP DVB-S DVB-S/C/TFront panel Displays, Operating Elements and ConnectionsRear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUXSide view MSK Observing angle of the on screen displayScreen Operating ConceptFrequently recurring softkeys Menu selection General information for operationMain menu Accu CAP % I=0.00 aMains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuseAccumulator operation Accumulator and Battery OperationDC socket option Connections Level measurement Measurement PossibilitiesMaximal input level Sat menu Sat OperationSelecting the LO frequency Setting of the LNB voltage supplyEntering the transponder frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROLLNB control menu KHz control signalLNB supply voltage LNB current drawCalling up the DiSEqC/V SEC menu Checking the LNB supply voltage of a satellite receiverDiSEqC DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field BSimple DiSEqC Example Entering and transmitting a DiSEqC commandData burst Tone burst General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 101390 Tx+rx CommandOperating the menus ModusSat Operation SEC menu Sending a V-SEC command TXEntering the hex numbers Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier MenuVideo polarity Second Anlaog menuSetting of the de-emphasis Audio carrier settingSat subcarrier menu Selecting the subcarrier recepAudio carrier table for reception type Audio carrier tables for the satellite receptionSAT Digital menu Digital Measurements27.500 SR Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chanTV-DiSEqC /VSEC menu TV control menuLNB U= 0.0 V I= 0 mA Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriersMeasuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacingSelecting demodulation for DVB-C measurement TV Digital menuMode Selecting channel bandwidths DVB-T optionalReturn path if menu Return Path if MenuAudio carrier table for if reception Analog menuMeasurement of the audio carrier spacing Measurement of the min./max. levelMeasurement of the current level Entering symbol rate QAM64 modeIf RP Digital Menu Radio menu Radio OperationRadio Analog menu Measuring the min/max level FM Measure ALLDecoder operation AV MenuDecoder operation baseband Video input Video outputRGB operation Breaking voltageMpeg transport stream interface TS-Parallel, Lvds optional PAT 08 Mpeg Decoder Menu Optional3sat KiKa Phoenix Unit Setting MenuOffset 0.0 dB Screen Menu Screen setupSetting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menuSaving the unit settings Saving and calling up unit settingsCalling up saved settings Copy MenuPrinting out all measurements in Sat mode Printing out all measurements in TV modeSpectr Mode MenuEnlarging the videotext Text MenuHolding the videotext Original videotext sizeHorizontal zoom Reducing the video signal Horizontal zoom -Enlarging the video signalScope Menu Video scope menuMeasurement of video signals via the AV socket Scart Measurement of the amplitude of the video signalSelecting the video line Time Audio ScopePos DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot ContMarker Span Spectral MenuMark AnaMarker dig Marker anaCross-polarisation measurement on signals in SAT operation Measurement of digital signals in Sat operationZoom marker Max offMeasurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairsCarrier offset Measurement of signal noise ratio SNRFrontend locked Inverting /not inverting a constellation diagram Selecting the symbol rate symbol-clockSelecting the code rate Examples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-CZoom Inverting /not inverting constellation diagramExamples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier modeHierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSKTrack MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33Cable system With return path capable amplifiers Display of the check point Auto MeasureModem / RS 232 interface InterfacesConnection cable for modem / RS Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menuTTY mode Code PasswordAnsi mode Log-in procedureRequesting help Example for logging-in in Ansi modeInterfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDUMaintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbonCommand overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical AppendixReset Reset DiSEqC minicontroller Command overview command byteCommand overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXRChannel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESBVHF UHF Channel and frequency table standard Lfrequency in MHzVII Channel and frequency table standard D/K frequency in MHzViii XIIChannel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Technical data Technical DataPower supply Qpsk BER SNRMER Scope of delivery AccessoriesAssignment of the Scart socket TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socketAssignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software9986498/0206 ZWT Subject to alterations