DreamGEAR MSK 33 manual 1390, Operating the menus, Modus, Tx+rx Command

Page 34

Sat Operation

Receiver field

Rec adr r-zf t0 t1 t2 st >02<244 1200 20 12 4 2

In the receiver field, the setting status of the receiver 01...12 simulated by the MSK 33 is displayed.

Refer to the example to the left:

The receiver 2 is registered in the head station with the address 244. The remote IF is 1200 MHz.

The collision pages are t0 = 20 ms, t1 = 12 ms and t2 = 4 ms. The status of the re- ceiver 2 is „registered.“

TX field

FRAME

ADD

COM

DATA

TX E2

00

F2

1390--

In the TX-field, the currently selected telegram of the respective receiver, 01...12, is displayed with the individual DiSEqC bytes and represented in combination with the individual DiSEqC commands.

The example shows: FRAME is E0 according to the programme commando (PrgCom). Address ADD is 00 (is reserved). Polarisation byte COM F2 complies with the selected polarisation and Sat planes. DATA complies with the set Sat IF in MHz.

Operating the menus

BACK

Modus

Exit the DiSEqC menu.

In the set UFOµ DiSEqC mode, the available remote IF frequency is adopted. In this case, the MSK 33 remains in the the UFOµ DiSEqC mode after exiting this menu and is still connected with the head end allowing standard measurements to be carried out. By repeatedly pressing this softkey (ring counter), select the UFOµ DiSEqC menu.

rx

tx+rx

Command

Command

>

Command

>

Command

> >

By quickly pressing this softkey, the monitoring function is switched on, in which the transmitted DiSEqC commands are recorded for a time period of up to 20 sec- onds. A maximum of 5 events (RX0…RX4) with respectively up to 6 bytes (Frame, Add, Com, Dat1, Dat2, Dat3) can be recorded between the head end and the available satellite receivers. During the recording, the command are displayed in the second line of the RX field by flashing.

The recording is automatically completed or prematurely cancelled by pressing down the softkey for a longer time.

With the buttons, ▲ and , the individual telegrams, RX 0…RX4, in the second line can be called up.

With the aid of this softkey, the selected telegram in the lower TX field is transmit- ted. If a message from the head station follows, the reply message is displayed in the RX field. The reply message is accordingly taken over in the receiver field, e.g. the remote IF.

By repeatedly pressing this softkey (ring counter), the DiSEqC telegram Virgin-Call- For-Address, Call-For-Address, Program-Command or Switch-Off is selected.

The respective telegram code is displayed in the TX field.

With this softkey, the cursor buttons, ▲▼ and ◄►, are switched on.

Independent from the selected telegram, different editing fields can be selected with the button, ◄ or ►. The selected fields are framed with arrows.

In the case of a programme command, the respective DiSEqC command, COM or DATA, can be edited. Select the editing field using the cursor button, ▼or ▲.

In the COM field, the polarisation byte, F0...FF, (horizontal/vertical/high/low) are se- lected with the aid of the cursor button, ▲ or ▼, and displayed in the softkey.

In DATA field, the Sat IF can directly changed in MHz via a numerical entry.

34

Image 34
Contents Operating manual Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 107 113Important Notes General safety informationExplanation of symbols Validity of this manualProper use Safety InstructionsConnections Mechanical loadbearing capacityFunctions FunctionsReturn path LP Functions overviewFunction DVB-S DVB-S/C/TDisplays, Operating Elements and Connections Front panelHeadphone connection Mains connection Mains switch DC socket Option / XLR-socketRear panel TS parallel Option 10 AUXObserving angle of the on screen display Side view MSKScreen Operating ConceptFrequently recurring softkeys Main menu General information for operationMenu selection Accu CAP % I=0.00 aOn/Off switch Place of installation of the MSKMains voltage / mains switch Safety fuseAccumulator operation Accumulator and Battery OperationDC socket option Connections Level measurement Measurement PossibilitiesMaximal input level Sat Operation Sat menuSelecting the LO frequency Setting of the LNB voltage supplyEntering the transponder frequency III Switch-over of Analog digit. DvbsBargraph Level range Comment Display Calling up menu LNB-CONTROLLNB supply voltage KHz control signalLNB control menu LNB current drawCalling up the DiSEqC/V SEC menu Checking the LNB supply voltage of a satellite receiverDiSEqC DiSEqC menu Display field a Submenu for entering DiSEqC commandsTX display field Display field BSimple DiSEqC Example Entering and transmitting a DiSEqC commandData burst Tone burst Display fields UFOmicro DiSEqC menuGeneral information RX 0 E2 10Operating the menus Tx+rx Command1390 ModusSat Operation SEC menu Sending a V-SEC command TXEntering the hex numbers Calling up the sound subcarrier Level-dependent acoustic signalInitial ANALOG-menu MenuSecond Anlaog menu Video polaritySat subcarrier menu Audio carrier settingSetting of the de-emphasis Selecting the subcarrier recepAudio carrier tables for the satellite reception Audio carrier table for reception typeSAT Digital menu Digital Measurements27.500 SR Level measurement Digital Min./Max. levels C10 210.25MHz A65.0dBµV TV OperationTV menu Rf chanTV-DiSEqC /VSEC menu TV control menuLNB U= 0.0 V I= 0 mA Audio carrier table for TV reception Analogue menuSelecting the standard Selecting the audio carriersSelecting the colour standards PAL, Secam and Ntsc Measuring the min./max. levelMeasuring the current level Measuring audio carrier spacingSelecting demodulation for DVB-C measurement TV Digital menuMode DVB-T optional Selecting channel bandwidthsReturn Path if Menu Return path if menuAnalog menu Audio carrier table for if receptionMeasurement of the audio carrier spacing Measurement of the min./max. levelMeasurement of the current level Entering symbol rate QAM64 modeIf RP Digital Menu Radio menu Radio OperationRadio Analog menu FM Measure ALL Measuring the min/max levelDecoder operation baseband Video input AV MenuDecoder operation Video outputRGB operation Breaking voltageMpeg transport stream interface TS-Parallel, Lvds optional PAT 08 Mpeg Decoder Menu Optional3sat KiKa Phoenix Unit Setting MenuOffset 0.0 dB Screen setup Screen MenuSystem Menu Setting the dateSetting the time Click button Calls up the SYS TEM menuCalling up saved settings Saving and calling up unit settingsSaving the unit settings Copy MenuPrinting out all measurements in TV mode Printing out all measurements in Sat modeMode Menu SpectrHolding the videotext Text MenuEnlarging the videotext Original videotext sizeScope Menu Horizontal zoom -Enlarging the video signalHorizontal zoom Reducing the video signal Video scope menuMeasurement of video signals via the AV socket Scart Measurement of the amplitude of the video signalSelecting the video line Time Audio ScopePos Saving function Position and triggering of the DiSEqC signalDiSEqC Scope Shot ContMark Spectral MenuMarker Span AnaMarker ana Marker digZoom marker Measurement of digital signals in Sat operationCross-polarisation measurement on signals in SAT operation Max offConst Menu Constellation diagram for Qpsk DVB-SMeasurement of the bit error rate BER Colour representation of I/Q value pairsCarrier offset Measurement of signal noise ratio SNRFrontend locked Inverting /not inverting a constellation diagram Selecting the symbol rate symbol-clockSelecting the code rate Examples for Qpsk constellation diagrams Constellation diagram for QAM DVB-C Measurement of modulation error rate MERInverting /not inverting constellation diagram ZoomExamples for QAM constellation diagram Const Menu Measurement of signal noise ration SNR Constellation diagram DVB-T optionalMeasurement of bit error rate BER Carrier modeHierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Broadband Cable Analysis Measuring System MSK Measuring principleTrack MVG10 MSK33 MVG10 Upstream measurementDownstream measurement RGB MSK33Cable system With return path capable amplifiers Auto Measure Display of the check pointModem / RS 232 interface InterfacesConnection cable for modem / RS Setting hardware handshake Setting baud rateSetting local echo Modem/RS232 menuAnsi mode Code PasswordTTY mode Log-in procedureExample for logging-in in Ansi mode Requesting helpInterfaces List of the command abbreviations STU RET Loading and saving predefined settingsSTU LDUMaintenance, Storage and Customer Service Printer paper-exchanging the ribbon Ribbon exchangeCommand overview address byte Overview of DiSEqC commandsCommand overview framing byte Technical AppendixCommand overview command byte Reset Reset DiSEqC minicontrollerCommand for Kathrein matrix 9xx-series DiSEqC commands for Kathrein matricesCommand overview data byte Command for Kathrein matrix EXRVHF-CCIR UHF-CCIR Channel tablesChannel and frequency table standard B/G frequency in MHz USB/OSB ESBChannel and frequency table standard Lfrequency in MHz VHF UHFViii Channel and frequency table standard D/K frequency in MHzVII XIIChannel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Technical data Technical DataPower supply Qpsk BER SNRMER Scope of delivery AccessoriesAssignment of the Scart socket Assignment of RS232 socket TXD RXD RTS CTS DSR GND DCD DTRAssignment of socket TS Parallel optional Unit variants Downloading New MSK33 Operating Software General notes9986498/0206 ZWT Subject to alterations