Allied Telesis AT-GS950/8 manual Copper, Fiber

Page 30

Chapter 3: Port Configuration

10M/Half - 10Mbps, half duplex

10M/Full - 10Mbps, full duplex

100M/Half - 100Mbps, half duplex

100M/Full - 100Mbps, full duplex

1000M/Full - 1000Mbps, full duplex

1000M_M/Full - 1000Mbps, full duplex for port operating as a Master port at 1000Mbps in Force mode. This allows the port to send detect and negotiate signals.

1000M_S/Full - 1000Mbps, full duplex for port operating as a Slave port at 1000Mbps in Force mode. This allows the port to receive negotiate signals.

5.To enable or disable flow control on the port, choose the port using the From and To lists. You can select one port (From 2 To 2, for example) or a range of ports (From 1 To 5, for example).

6.From the Flow Control list, choose one of the following:

Enabled

Flow control is enabled.

Disabled

Flow control is disabled. This is the default.

7.From the Medium Type list, choose one of the following:

Note

This setting applies only to the SFP ports, ports 7 and 8, shown as ports 7F and 8F in the Port Configuration page.

Copper

Copper SFP.

Fiber

Fiber SFP.

8.Click Apply to implement your changes.

9.To save the settings to the configuration file, from the main menu, select Save Configuration.

The Save Configuration page is shown in Figure 3 on page 14.

10.Click Apply.

30

Image 30

Contents Management Software Page Contents Contents Figures Figures Preface Where to Find Web-based Guides Management Software Updates Contacting Allied TelesisPreface Getting Started ChapterStarting a Management Session Main Save Configuration Click Apply Saving ChangesQuitting a Management Session Getting Started Basic Switch Parameters Basic Switch Parameters AT-S82 Management Software User’s Guide Enabled DisabledDisabling or Enabling Ping Blocking Enabling or Disabling 802.1X Forwarding Control Changing the Administrator’s Password Rebooting the Switch Resetting the Switch and Retaining the IP Address Reset Click Apply Switch is resetAT-S82 Management Software User’s Guide Downloading New Firmware Download Status Message Port Configuration Configuring Port Parameters Port is enabled. This is the default Copper FiberTrunking Trunking Overview Trunking Guidelines Trunking AlgorithmAT-S82 Management Software User’s Guide Configuring the Trunking Algorithm DAxorSASetting up the Trunk Port Trunking ConfigurationTrunking Port Mirroring Port Mirroring Overview Configuring Port Mirroring Port Mirroring VLANs Vlan Features Increased Performance Improved Manageability SecurityAT-S82 Management Software User’s Guide Vlan Overview Vlan Identifier Vlan Port MembersIncoming Outgoing Tagged Untagged Frames Guidelines for Creating a Vlan Working with VLANs Vlan DetailDisplaying all VLANs Click Show All Static Vlan EntriesVlan Protected Ports Vlan Protected Ports Vlan ExampleAT-S82 Management Software User’s Guide VLANs Class of Service Class of Service Overview Mapping Ports to Egress QueuesIeee 802.1p Priority Level Port Priority Queue Port Egress Queue Maximum Number Packets Mapping Priorities to Queues Setting Up the Schedule Assigning Priority to Ports Class of Service Spanning Tree Protocol STP Spanning Tree Overview Bridge Priority RootPath Costs and Port Costs Increment Bridge PriorityPort Speed Port Cost Port Priority Increment Port PriorityHello Time and Bridge Protocol Data Units BPDUs Point-to-Point and Edge Ports Edge Port Spanning Tree and VLANs Spanning Tree Protocol STP Configuring Spanning Tree Rstp STP CompatibleDisabled Configuring STP Port Settings True YesFalse AutoSpanning Tree Protocol STP

Related manuals

Manual 44 pages 22.06 Kb