Allied Telesis 86241-06 manual Disable DS3 Debug Disable DS3 Test Enable DS3 Debug

Page 27

Patch 86241-06 For Rapier Switches

27

The PARAM24 parameter specifies the 24-hour counter threshold for all performance monitoring parameters (PES, PSES, SEF, UAS, LES, CES, CSES) between 1 and 65535 seconds inclusive. If a trigger has been created, it will assert if the 24-hour count exceeds the value specified in PARAM24. The default is 65535 seconds.

The PORT parameter specifies from which port a test signal is generated, and is 0 to 38 characters in length. This parameter is only valid if the TYPE parameter is set to TSID. This parameter is only meaningful with the CMTCE parameter set to ON. With CMTCE set to OFF this parameter is ignored. The default pattern is “ignore”.

The PRIM15 parameter specifies the 15-minute counter threshold for all performance monitoring primitives (LCV, PCV, CCV) between 1 and 16383 seconds inclusive. If a trigger has been created, it will assert if the 15-minute count exceeds the value specified in PRIM15. The default is 16383.

The PRIM24 parameter specifies the 24-hour counter threshold for all performance monitoring primitives (LCV, PCV, CCV) between 1 and 1048575 seconds inclusive. If a trigger has been created, it will assert if the 24-hour count exceeds the value specified in PRIM24. The default is 1048575.

The PRIM24 parameter specifies the 24-hour counter threshold for all performance monitoring primitives (LCV, PCV, CCV) between 0 and 1048575 seconds. If a trigger has been created, it will assert if the 24-hour count exceeds the value specified in PRIM24. The default is 1048575.

The TYPE parameter is used with the EIC, FAC, FIC, LIC, or UNIT parameters to specify whether the text string is used to describes a path signal, an idle signal, or a test signal.

The UNIT parameter specifies where the equipment is located within a bay e.g. “SHELF6”, and is 0 to 6 characters in length. This parameter is only meaningful with the CMTCE parameter set to ON. With CMTCE set to OFF this parameter is ignored. The default pattern is “ignore”.

To see the current configuration use the command:

SHOW DS3=n STATE

The DS3 counters can be displayed by using the command:

SHOW DS3=n COUNTERS [HISTORY[=interval]] {NEARFARBOTH}

The counters can be reset by using the command

RESET DS3[=instance]

COUNTERS[={HDLCINTERFACELINKDIAGNOSTICSTATEALL}]

where:

■instance is the number of the DS3 interface.

A further description of DS3 can be found in the DS3 Interfaces section of

Chapter 5, Interfaces in your switch’s software reference.

The commands used to set up and configure the DS3 interface are:

■DISABLE DS3 DEBUG

■DISABLE DS3 TEST

■ENABLE DS3 DEBUG

Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Patch For Rapier Switches PCR Module BGP Level PCR Module IPG LevelPCR Module SWI PCR Module PIM LevelPCR Module Utility Level PCR Module SSH LevelPCR 03064 Module Snmp Level PCR Module SWI LevelPCR 03113 Module Dvmrp Level PCR 03100 Module Dhcp LevelPCR Module FR, PPP Level PCR 03108 Module Mlds LevelPCR Module Ospf Level PCR 03123 Module Dhcp LevelPCR Module DS3 Level PCR Module IPV6 LevelPCR Module IPG, SWI, Vlan Network affecting No PCR 02315 Module Snmp Network affecting NoPCR Module DS3 Network affecting No PCR Module IPv6, SWI, IPG, Vlan Network affecting NoPCR Module Firewall Network affecting No PCR Module Install Network affecting NoPCR Module User Network affecting No PCR Module Utility Network affecting NoPCR Module Ping Network affecting No PCR Module IPG Network affecting NoPCR Module Network affecting No PCR Module Ospf IPG Network affecting NoPCR 02532 Module FIREWALLNetwork affecting No PCR 02523 Module QOS, Utility Network affecting NoPCR Module TELNET, PING, IPV6, Network affecting No PCR 02529 Module FIREWALLNetwork affecting NoPCR Module SWI Network affecting No PCR 02538 Module Dvmrp Network affecting NoPCR Module Classifier Network affecting No PCR Module IPV6 Network affecting NoPCR 02467 Module Core Network affecting No PCR 02574 Module DVMRPNetwork affecting NoPCR 02579 Module FIREWALLNetwork affecting No PCR 02587 Module OSPFNetwork affecting NoPCR 02498 Module Vlan Network affecting No PCR 02469 Module TMNetwork affecting NoPCR Module IPG, PIM, SWI Network affecting No PCR 02495 Module Vlan Network affecting NoPCR Module Vrrp Network affecting No PCR 02502 Module Ping, IPv6Network affecting NoPCR 02509 Module DVMRPNetwork affecting No PCR Module DNS Relay Network affecting NoPCR Module TELNET, TTY Network affecting No PCR Module BGP Network affecting NoPCR Module Tpad Network affecting No PCR 02277 Module Dvmrp Network affecting NoPCR 02301 Module IPGNetwork affecting No PCR 02303 Module INSTALLNetwork affecting NoPCR 02292 Module IPSECNetwork affecting No PCR 02294 Module IKMPNetwork affecting NoPCR Module Ipsec Network affecting No PCR Module FR Network affecting NoPCR Module IPG/FIREWALL Network affecting No PCR Module IPG, ETH Network affecting NoPCR Module SCC, SYN, PPP Network affecting No PCR Module PPP Network affecting NoPCR Module BGP, IPG Network affecting No PCR 02348 Module Enco Network affecting NoPCR Module FFS, FILE, TTY Network affecting No PCR Module VRRP, TRG Network affecting NoPCR 02397 Module Dvmrp Network affecting No PCR Module IPG Network affecting No Module Vrrp PCR Module Trace Network affecting NoPCR Module SNMP, CORE, SHOW, Network affecting No PCR Module STP Network affecting NoPCR 02463 Module DVMRP, IPG Network affecting No PCR 02450 Module IPV6Network affecting NoPCR 02452 Module IPv6Network affecting No PCR 02457 Module IPV6Network affecting NoPCR Module Switch Network affecting No PCR Module DHCP, IPG Network affecting No DS3 InterfacesBit Parity Mode Loopbacks DS3 Configuration Patch Release Note Disable DS3 Debug Disable DS3 Test Enable DS3 Debug Create Framerelay Show Framerelay Dynamic Port Security Availability
Top Page Image Contents