Advantech EKI-7657C user manual Safety Instructions

Page 5

Safety Instructions

1.Read these safety instructions carefully.

2.Keep this User's Manual for later reference.

3.Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.

4.For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.

5.Keep this equipment away from humidity.

6.Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.

7.The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.

8.Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

9.Position the power cord so that people cannot step on it. Do not place anything over the power cord.

10.All cautions and warnings on the equipment should be noted.

11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12.Never pour any liquid into an opening. This may cause fire or electrical shock.

13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14.If one of the following situations arises, get the equipment checked by service personnel:

a.The power cord or plug is damaged.

b.Liquid has penetrated into the equipment.

c.The equipment has been exposed to moisture.

d.The equipment does not work well, or you cannot get it to work according to the user's manual.

e.The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15.DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE

TEMPERATURE MAY GO BELOW -40 (-40 ) OR ABOVE 85 (185 ). THIS

COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

v

Image 5

Contents EKI-7657C Copyright Acknowledgements Product Warranty 2 years FCC Class a Technical Support and Assistance Declaration of ConformitySafety Instructions Safety Precaution Static Electricity Contents Chapter Commands Level Port Troubleshooting Overview Introduction Dual Power InputSFP Advantage High-Speed TransmissionsEasy Troubleshooting Wide Operating TemperatureFlexible Mounting Advanced ProtectionFeatures Power Specification CommunicationsInterface MechanismCertifications EnvironmentPacking List Safety PrecautionEKI-7657C Manualed1 Installation EKI-7657C LED Definition LED IndicatorsFront View of EKI-7657C Dimensions units mmSide View of EKI-7657C Rear View of EKI-7657C Top View of EKI-7657C Wall mounting MountingDIN-rail Mounting Installation to DIN-rail StepInstallation to DIN-rail Step Connection to a Fiber Optic Network Network ConnectionTransceiver Inserted 11 Remove LC connector 13 Pin Assignment of the Power Connector Power Connection14 Pin Assignment of the Dido Connector Wiring the Digital Inputs/OutputsPage Configuration RS-232 Console ConfigurationCOM Port Properties Setting Command Level Commands LevelSystem Commands Set Commands Set ListCommands Set List System Commands SetPort Commands Set Port Commands SetTrunk Commands Set Trunk Commands SetVlan Commands Set Vlan Commands SetSpanning Tree Commands Set Spanning Tree Commands SetIgmp Commands Set QOS Commands Set10 Mac/Filter Table Commands Set QOS Commands Set11 Snmp Commands Set Snmp Commands Set10 Mac/Filter Table Commands Set 13 802.1x Commands Set Port Mirroring Commands Set12 Port Mirroring Commands Set 13 802.1x Commands Set14 Tftp Commands Set Tftp Commands Set15 SysLog,SMTP,Event Commands Set SystemLog, Smtp and Event16 Sntp Commands Set Sntp Commands Set17 X-ring Commands Set Ring Commands SetWeb Browser Management will not be configuredMain System Information SystemIP Configuration IP ConfigurationDhcp Client-System Configuration Dhcp Server-System configurationDhcp Server-Port and IP Bindings 11 Dhcp Server Client EntriesTFTP-Restore Configuration TFTP-Update FirmwareTFTP-Backup Configuration 14 Tftp Restore ConfigurationSystem Event Log-SMTP Configuration System Event Log-Syslog ConfigurationSystem Event Log-Event Configuration 17 Smtp ConfigurationFault Relay Alarm 18 Event Configuration19 Fault Relay Alarm 18 UTC Timezone Sntp Configuration20 Sntp Configuration 21 IP Security IP Security22 User Authentication User AuthenticationDigital Output Digital Input/OutputDigital Input 23 Digital Input/Output interface Port Statistics Port25 Port Control Port ControlPort Trunk Aggregator settingAggregator Information 26 2 work ports with Lacp enabledPassive State Activity30 State Activity 31 Port Mirroring Port Mirroring32 Rate Limiting Rate LimitingProtocol Vlan configurationVlan configuration Port-based Vlan 34 Port based mode 35 Port based mode-Add interface 802.1Q Vlan 802.1Q ConfigurationGroup Configuration 37 802.1Q Vlan ConfigurationRapid Spanning Tree 38 Edit Group Configuration interfacePage RSTP-Port Configuration RSTP-System Configuration41 Rstp Port Configuration interface System Configuration Community Strings Snmp ConfigurationAgent Mode Trap ConfigurationUser Profile SNMPV3 ConfigurationContext Table Group Table 44 Snmp V3 Configuration interfaceMIBview Table Access TableQoS Policy and Priority Type QoS ConfigurationPort Base Priority COS ConfigurationTOS Configuration 19 Igmp types Igmp ConfigurationRing 47 X-ring interface 48 Lldp Configuration interface Lldp Configuration802.1X/Radius System Configuration 802.1X/Radius Configuration802.1x/Radius-Port Configuration Security802.1X/Radius-Misc Configuration 50 802.1x/Radius Port Setting interface51 802.1x/Radius Misc Configuration interface MAC Address Table-MAC Filtering MAC Address TableMAC Address Table-Static MAC Address MAC Address Table-All MAC Addresses 53 MAC Filtering interface55 All MAC Address interface MAC Address Table-Multicast Filtering56 Factory Default interface Factory Default57 Save Configuration interface Save Configuration58 System Reboot interface System RebootTroubleshooting Diagnosing LED Indicators Pin Assignment & Wiring Appendix a Pin Assignment & Wiring Figure A.4 DB 9-pin female connector EKI-7657C Manualed1 Compatible SFP Modules Appendix B Compatible SFP Modules