Advantech EKI-7657C user manual Port Control

Page 68

Port Control

In Port Control, you can pull down the selection items to set the parameters of each port to control the transmitting/receiving packets.

• Port: Select the port that you want to configure.
• State: Current port status. The port can be set to disable or enable mode. If the port state is set as
•	‘Disable’, it will not receive or transmit any packet.
	Negotiation: Auto and Force. Being set as Auto, the speed and duplex mode are negotiated
	automatically. When you set it as Force, you have to assign the speed and duplex mode manually.
• Speed: It is available for selecting when the Negotiation column is set as Force. When the Negotiation
	column is set as Auto, this column is read only.
• Duplex: It is available for selecting when the Negotiation column is set as Force. When the Negotiation
	column is set as Auto, this column is read only.
• Flow Control: Set flow control function as Enable or Disable. When enabled, once the device exceed
	the input data rate of another device as a result the receiving device will send a PAUSE frame which
	halts the transmission of the sender for a specified period of time. When disabled, the receiving device
	will drop the packet if too much to process.
• Security: Once the Security selection is set as ‘On’, any access from the device which connects to this
	port will be blocked unless the MAC address of the device is included in the static MAC address table.
	See the segment of Static MAC Table.
•	Click	媖	to make the configuration effective.

Figure 3.25: Port Control

EKI-7657C _Manual_ed1

58

Image 68

Contents EKI-7657C Copyright Acknowledgements Product Warranty 2 years Declaration of Conformity FCC Class a Technical Support and AssistanceSafety Instructions Safety Precaution Static Electricity Contents Chapter Commands Level Port Troubleshooting Overview Dual Power Input IntroductionSFP Advantage High-Speed TransmissionsWide Operating Temperature Easy TroubleshootingFlexible Mounting Advanced ProtectionFeatures Specification Communications PowerInterface MechanismEnvironment CertificationsSafety Precaution Packing ListEKI-7657C Manualed1 Installation LED Indicators EKI-7657C LED DefinitionDimensions units mm Front View of EKI-7657CSide View of EKI-7657C Rear View of EKI-7657C Top View of EKI-7657C Mounting Wall mountingInstallation to DIN-rail Step DIN-rail MountingInstallation to DIN-rail Step Network Connection Connection to a Fiber Optic NetworkTransceiver Inserted 11 Remove LC connector Power Connection 13 Pin Assignment of the Power ConnectorWiring the Digital Inputs/Outputs 14 Pin Assignment of the Dido ConnectorPage Configuration Configuration RS-232 ConsoleCOM Port Properties Setting Commands Level Command LevelCommands Set List System Commands SetCommands Set List System Commands SetPort Commands Set Port Commands SetTrunk Commands Set Trunk Commands SetVlan Commands Set Vlan Commands SetSpanning Tree Commands Set Spanning Tree Commands SetQOS Commands Set Igmp Commands Set10 Mac/Filter Table Commands Set QOS Commands Set11 Snmp Commands Set Snmp Commands Set10 Mac/Filter Table Commands Set Port Mirroring Commands Set 13 802.1x Commands Set12 Port Mirroring Commands Set 13 802.1x Commands SetTftp Commands Set 14 Tftp Commands Set15 SysLog,SMTP,Event Commands Set SystemLog, Smtp and EventSntp Commands Set 16 Sntp Commands SetRing Commands Set 17 X-ring Commands SetManagement will not be configured Web BrowserMain System System InformationIP Configuration IP ConfigurationDhcp Server-System configuration Dhcp Client-System Configuration11 Dhcp Server Client Entries Dhcp Server-Port and IP BindingsTFTP-Update Firmware TFTP-Restore Configuration14 Tftp Restore Configuration TFTP-Backup ConfigurationSystem Event Log-Syslog Configuration System Event Log-SMTP Configuration17 Smtp Configuration System Event Log-Event Configuration18 Event Configuration Fault Relay Alarm19 Fault Relay Alarm Sntp Configuration 18 UTC Timezone20 Sntp Configuration IP Security 21 IP SecurityUser Authentication 22 User AuthenticationDigital Output Digital Input/OutputDigital Input 23 Digital Input/Output interface Port Port StatisticsPort Control 25 Port ControlAggregator setting Port Trunk26 2 work ports with Lacp enabled Aggregator InformationState Activity Passive30 State Activity Port Mirroring 31 Port MirroringRate Limiting 32 Rate LimitingProtocol Vlan configurationVlan configuration Port-based Vlan 34 Port based mode 35 Port based mode-Add interface 802.1Q Configuration 802.1Q Vlan37 802.1Q Vlan Configuration Group Configuration38 Edit Group Configuration interface Rapid Spanning TreePage RSTP-System Configuration RSTP-Port Configuration41 Rstp Port Configuration interface Snmp Configuration System Configuration Community StringsAgent Mode Trap ConfigurationUser Profile SNMPV3 ConfigurationContext Table 44 Snmp V3 Configuration interface Group TableAccess Table MIBview TableQoS Configuration QoS Policy and Priority TypePort Base Priority COS ConfigurationTOS Configuration Igmp Configuration 19 Igmp typesRing 47 X-ring interface Lldp Configuration 48 Lldp Configuration interface802.1X/Radius Configuration 802.1X/Radius System Configuration802.1x/Radius-Port Configuration Security50 802.1x/Radius Port Setting interface 802.1X/Radius-Misc Configuration51 802.1x/Radius Misc Configuration interface MAC Address Table-MAC Filtering MAC Address TableMAC Address Table-Static MAC Address 53 MAC Filtering interface MAC Address Table-All MAC AddressesMAC Address Table-Multicast Filtering 55 All MAC Address interfaceFactory Default 56 Factory Default interfaceSave Configuration 57 Save Configuration interfaceSystem Reboot 58 System Reboot interfaceTroubleshooting Diagnosing LED Indicators Pin Assignment & Wiring Appendix a Pin Assignment & Wiring Figure A.4 DB 9-pin female connector EKI-7657C Manualed1 Compatible SFP Modules Appendix B Compatible SFP Modules