Advantech EKI-7657C user manual IP Configuration

Page 52

IP Configuration

User can configure the IP Settings and DHCP client function here.

•DHCP Client: Enable or disable the DHCP client function. When DHCP client function is enabled, the industrial switch will be assigned an IP address from the network DHCP server. The default IP address will be replaced by the assigned IP address on DHCP server. After user click Apply, a popup dialog shows up. It is to inform the user that when the DHCP client is enabled, the current IP will lose and user should find the new IP on the DHCP server.

•IP Address: Assign the IP address that the network is using. If DHCP client function is enabled, and then the user doesn’t need to assign the IP address. And, the network DHCP server will assign the IP address displaying in this column for the industrial switch. The default IP is 192.168.16.1.

•Subnet Mask: Assign the subnet mask to the IP address. If DHCP client function is enabled, and then the user does not need to assign the subnet mask.

•Gateway: Assign the network gateway for the industrial switch. The default gateway is 192.168.16.254.

•DNS1: The abbreviation of Domain Name Server—an Internet service that translate domain name into IP addresses. Domain name are alphabetic which are easy to be remembered. Because the Internet is based on IP address; every time you use a domain name, therefore, a DNS service must translate the name into the corresponding IP address. For example, the domain name www.net.com might translate to 192.168.1.1

•DNS2: The backup for DNS1. When DNS1 cannot function, DNS2 will then replace DNS1 immediately.

•And then, click

媖

Figure 3.9: IP Configuration

EKI-7657C _Manual_ed1

42

Image 52

Contents EKI-7657C Copyright Acknowledgements Product Warranty 2 years Declaration of Conformity FCC Class a Technical Support and AssistanceSafety Instructions Safety Precaution Static Electricity Contents Chapter Commands Level Port Troubleshooting Overview Dual Power Input IntroductionSFP Advantage High-Speed TransmissionsWide Operating Temperature Easy TroubleshootingFlexible Mounting Advanced ProtectionFeatures Specification Communications PowerInterface MechanismEnvironment CertificationsSafety Precaution Packing ListEKI-7657C Manualed1 Installation LED Indicators EKI-7657C LED DefinitionDimensions units mm Front View of EKI-7657CSide View of EKI-7657C Rear View of EKI-7657C Top View of EKI-7657C Mounting Wall mountingInstallation to DIN-rail Step DIN-rail MountingInstallation to DIN-rail Step Network Connection Connection to a Fiber Optic NetworkTransceiver Inserted 11 Remove LC connector Power Connection 13 Pin Assignment of the Power ConnectorWiring the Digital Inputs/Outputs 14 Pin Assignment of the Dido ConnectorPage Configuration Configuration RS-232 ConsoleCOM Port Properties Setting Commands Level Command LevelCommands Set List System Commands SetCommands Set List System Commands SetPort Commands Set Port Commands SetTrunk Commands Set Trunk Commands SetVlan Commands Set Vlan Commands SetSpanning Tree Commands Set Spanning Tree Commands SetQOS Commands Set Igmp Commands Set10 Mac/Filter Table Commands Set QOS Commands Set10 Mac/Filter Table Commands Set Snmp Commands Set11 Snmp Commands Set Port Mirroring Commands Set 13 802.1x Commands Set12 Port Mirroring Commands Set 13 802.1x Commands SetTftp Commands Set 14 Tftp Commands Set15 SysLog,SMTP,Event Commands Set SystemLog, Smtp and EventSntp Commands Set 16 Sntp Commands SetRing Commands Set 17 X-ring Commands SetManagement will not be configured Web BrowserMain System System InformationIP Configuration IP ConfigurationDhcp Server-System configuration Dhcp Client-System Configuration11 Dhcp Server Client Entries Dhcp Server-Port and IP BindingsTFTP-Update Firmware TFTP-Restore Configuration14 Tftp Restore Configuration TFTP-Backup ConfigurationSystem Event Log-Syslog Configuration System Event Log-SMTP Configuration17 Smtp Configuration System Event Log-Event Configuration18 Event Configuration Fault Relay Alarm19 Fault Relay Alarm Sntp Configuration 18 UTC Timezone20 Sntp Configuration IP Security 21 IP SecurityUser Authentication 22 User AuthenticationDigital Input Digital Input/OutputDigital Output 23 Digital Input/Output interface Port Port StatisticsPort Control 25 Port ControlAggregator setting Port Trunk26 2 work ports with Lacp enabled Aggregator InformationState Activity Passive30 State Activity Port Mirroring 31 Port MirroringRate Limiting 32 Rate LimitingVlan configuration Port-based Vlan Vlan configurationProtocol 34 Port based mode 35 Port based mode-Add interface 802.1Q Configuration 802.1Q Vlan37 802.1Q Vlan Configuration Group Configuration38 Edit Group Configuration interface Rapid Spanning TreePage RSTP-System Configuration RSTP-Port Configuration41 Rstp Port Configuration interface Snmp Configuration System Configuration Community StringsAgent Mode Trap ConfigurationContext Table SNMPV3 ConfigurationUser Profile 44 Snmp V3 Configuration interface Group TableAccess Table MIBview TableQoS Configuration QoS Policy and Priority TypeTOS Configuration COS ConfigurationPort Base Priority Igmp Configuration 19 Igmp typesRing 47 X-ring interface Lldp Configuration 48 Lldp Configuration interface802.1X/Radius Configuration 802.1X/Radius System Configuration802.1x/Radius-Port Configuration Security50 802.1x/Radius Port Setting interface 802.1X/Radius-Misc Configuration51 802.1x/Radius Misc Configuration interface MAC Address Table-Static MAC Address MAC Address TableMAC Address Table-MAC Filtering 53 MAC Filtering interface MAC Address Table-All MAC AddressesMAC Address Table-Multicast Filtering 55 All MAC Address interfaceFactory Default 56 Factory Default interfaceSave Configuration 57 Save Configuration interfaceSystem Reboot 58 System Reboot interfaceTroubleshooting Diagnosing LED Indicators Pin Assignment & Wiring Appendix a Pin Assignment & Wiring Figure A.4 DB 9-pin female connector EKI-7657C Manualed1 Compatible SFP Modules Appendix B Compatible SFP Modules