Advantech EKI-7657C System Event Log-Syslog Configuration, System Event Log-SMTP Configuration

Page 57

System Event Log—Syslog Configuration

Configure the system event mode to collect system log.


• Syslog Client Mode: Select the system log mode—Client Only, Server Only, or Both.
• System Log Server IP Address: Assign the system log server IP.
•	When Syslog Client Mode is set as Client Only, the system event log will only be reserved in the
	switch’s RAM until next reboot. When Syslog Client Mode is set as Server Only, the system log will
	only be sent to the syslog server and you have to type the IP address in the Sysylog Server IP Address
	column. If the Syslog Client Mode is set as Both, the system log will be reserved in the switch’s RAM
	and sent to server.
•	Click	Reload	to refresh the events log.
•	Click	Clear	to clear all current events log.
•	After configuring, click			媖	.

Figure 3.16: Syslog Configuration

System Event Log—SMTP Configuration

You can set up the mail server IP, mail account, password, and forwarded email account for receiving the event alert.

•Email Alert: Enable or disable the email alert function.

•SMTP Server IP: Set up the mail server IP address (when Email Alert enabled, this function will then be available).

47

Chapter3

Image 57

Contents EKI-7657C Copyright Acknowledgements Product Warranty 2 years FCC Class a Technical Support and Assistance Declaration of ConformitySafety Instructions Safety Precaution Static Electricity Contents Chapter Commands Level Port Troubleshooting Overview Introduction Dual Power InputSFP Advantage High-Speed TransmissionsEasy Troubleshooting Wide Operating TemperatureFlexible Mounting Advanced ProtectionFeatures Power Specification CommunicationsInterface MechanismCertifications EnvironmentPacking List Safety PrecautionEKI-7657C Manualed1 Installation EKI-7657C LED Definition LED IndicatorsFront View of EKI-7657C Dimensions units mmSide View of EKI-7657C Rear View of EKI-7657C Top View of EKI-7657C Wall mounting MountingDIN-rail Mounting Installation to DIN-rail StepInstallation to DIN-rail Step Connection to a Fiber Optic Network Network ConnectionTransceiver Inserted 11 Remove LC connector 13 Pin Assignment of the Power Connector Power Connection14 Pin Assignment of the Dido Connector Wiring the Digital Inputs/OutputsPage Configuration RS-232 Console ConfigurationCOM Port Properties Setting Command Level Commands LevelSystem Commands Set Commands Set ListCommands Set List System Commands SetPort Commands Set Port Commands SetTrunk Commands Set Trunk Commands SetVlan Commands Set Vlan Commands SetSpanning Tree Commands Set Spanning Tree Commands SetIgmp Commands Set QOS Commands Set10 Mac/Filter Table Commands Set QOS Commands SetSnmp Commands Set 10 Mac/Filter Table Commands Set11 Snmp Commands Set 13 802.1x Commands Set Port Mirroring Commands Set12 Port Mirroring Commands Set 13 802.1x Commands Set14 Tftp Commands Set Tftp Commands Set15 SysLog,SMTP,Event Commands Set SystemLog, Smtp and Event16 Sntp Commands Set Sntp Commands Set17 X-ring Commands Set Ring Commands SetWeb Browser Management will not be configuredMain System Information SystemIP Configuration IP ConfigurationDhcp Client-System Configuration Dhcp Server-System configurationDhcp Server-Port and IP Bindings 11 Dhcp Server Client EntriesTFTP-Restore Configuration TFTP-Update FirmwareTFTP-Backup Configuration 14 Tftp Restore ConfigurationSystem Event Log-SMTP Configuration System Event Log-Syslog ConfigurationSystem Event Log-Event Configuration 17 Smtp ConfigurationFault Relay Alarm 18 Event Configuration19 Fault Relay Alarm 18 UTC Timezone Sntp Configuration20 Sntp Configuration 21 IP Security IP Security22 User Authentication User AuthenticationDigital Input/Output Digital InputDigital Output 23 Digital Input/Output interface Port Statistics Port25 Port Control Port ControlPort Trunk Aggregator settingAggregator Information 26 2 work ports with Lacp enabledPassive State Activity30 State Activity 31 Port Mirroring Port Mirroring32 Rate Limiting Rate LimitingVlan configuration Vlan configuration Port-based VlanProtocol 34 Port based mode 35 Port based mode-Add interface 802.1Q Vlan 802.1Q ConfigurationGroup Configuration 37 802.1Q Vlan ConfigurationRapid Spanning Tree 38 Edit Group Configuration interfacePage RSTP-Port Configuration RSTP-System Configuration41 Rstp Port Configuration interface System Configuration Community Strings Snmp ConfigurationAgent Mode Trap ConfigurationSNMPV3 Configuration Context TableUser Profile Group Table 44 Snmp V3 Configuration interfaceMIBview Table Access TableQoS Policy and Priority Type QoS ConfigurationCOS Configuration TOS ConfigurationPort Base Priority 19 Igmp types Igmp ConfigurationRing 47 X-ring interface 48 Lldp Configuration interface Lldp Configuration802.1X/Radius System Configuration 802.1X/Radius Configuration802.1x/Radius-Port Configuration Security802.1X/Radius-Misc Configuration 50 802.1x/Radius Port Setting interface51 802.1x/Radius Misc Configuration interface MAC Address Table MAC Address Table-Static MAC AddressMAC Address Table-MAC Filtering MAC Address Table-All MAC Addresses 53 MAC Filtering interface55 All MAC Address interface MAC Address Table-Multicast Filtering56 Factory Default interface Factory Default57 Save Configuration interface Save Configuration58 System Reboot interface System RebootTroubleshooting Diagnosing LED Indicators Pin Assignment & Wiring Appendix a Pin Assignment & Wiring Figure A.4 DB 9-pin female connector EKI-7657C Manualed1 Compatible SFP Modules Appendix B Compatible SFP Modules