Advantech EKI-7657C user manual State Activity, Passive

Page 71

Figure 3.28: Static trunking group of 2 ports on single switch

When you have set up the aggregator setting of two interconnected switches with LACP enabled, you will see the respective LACP trunk group information as below. ‘Actor’ means the switch which is connecting to the host computer.

Figure 3.29: Aggregator Information

State Activity

Having set up the LACP aggregator on the tab of Aggregator Setting, you can configure the state activity for the members of the LACP trunk group. You can tick or cancel the checkbox beside the state display.

When you remove the tick mark to the port and click

Passive.

媖	, the port state activity will change to

•Active: The port automatically sends LACP protocol packets.

•Passive: The port does not automatically send LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device.

Note	A link having either two active LACP nodes or one active node can perform
	dynamic LACP trunk.
	A link having two passive LACP nodes will not perform dynamic LACP trunk
	61	Chapter3

Image 71

Contents EKI-7657C Copyright Acknowledgements Product Warranty 2 years FCC Class a Technical Support and Assistance Declaration of ConformitySafety Instructions Safety Precaution Static Electricity Contents Chapter Commands Level Port Troubleshooting Overview High-Speed Transmissions Dual Power InputIntroduction SFP AdvantageAdvanced Protection Wide Operating TemperatureEasy Troubleshooting Flexible MountingFeatures Mechanism Specification CommunicationsPower InterfaceCertifications EnvironmentPacking List Safety PrecautionEKI-7657C Manualed1 Installation EKI-7657C LED Definition LED IndicatorsFront View of EKI-7657C Dimensions units mmSide View of EKI-7657C Rear View of EKI-7657C Top View of EKI-7657C Wall mounting MountingDIN-rail Mounting Installation to DIN-rail StepInstallation to DIN-rail Step Connection to a Fiber Optic Network Network ConnectionTransceiver Inserted 11 Remove LC connector 13 Pin Assignment of the Power Connector Power Connection14 Pin Assignment of the Dido Connector Wiring the Digital Inputs/OutputsPage Configuration RS-232 Console ConfigurationCOM Port Properties Setting Command Level Commands LevelSystem Commands Set Commands Set ListSystem Commands Set Commands Set ListPort Commands Set Port Commands SetTrunk Commands Set Trunk Commands SetVlan Commands Set Vlan Commands SetSpanning Tree Commands Set Spanning Tree Commands SetQOS Commands Set QOS Commands SetIgmp Commands Set 10 Mac/Filter Table Commands Set11 Snmp Commands Set Snmp Commands Set10 Mac/Filter Table Commands Set 13 802.1x Commands Set Port Mirroring Commands Set13 802.1x Commands Set 12 Port Mirroring Commands SetSystemLog, Smtp and Event Tftp Commands Set14 Tftp Commands Set 15 SysLog,SMTP,Event Commands Set16 Sntp Commands Set Sntp Commands Set17 X-ring Commands Set Ring Commands SetWeb Browser Management will not be configuredMain System Information SystemIP Configuration IP ConfigurationDhcp Client-System Configuration Dhcp Server-System configurationDhcp Server-Port and IP Bindings 11 Dhcp Server Client EntriesTFTP-Restore Configuration TFTP-Update FirmwareTFTP-Backup Configuration 14 Tftp Restore ConfigurationSystem Event Log-SMTP Configuration System Event Log-Syslog ConfigurationSystem Event Log-Event Configuration 17 Smtp ConfigurationFault Relay Alarm 18 Event Configuration19 Fault Relay Alarm 18 UTC Timezone Sntp Configuration20 Sntp Configuration 21 IP Security IP Security22 User Authentication User AuthenticationDigital Output Digital Input/OutputDigital Input 23 Digital Input/Output interface Port Statistics Port25 Port Control Port ControlPort Trunk Aggregator settingAggregator Information 26 2 work ports with Lacp enabledPassive State Activity30 State Activity 31 Port Mirroring Port Mirroring32 Rate Limiting Rate LimitingProtocol Vlan configurationVlan configuration Port-based Vlan 34 Port based mode 35 Port based mode-Add interface 802.1Q Vlan 802.1Q ConfigurationGroup Configuration 37 802.1Q Vlan ConfigurationRapid Spanning Tree 38 Edit Group Configuration interfacePage RSTP-Port Configuration RSTP-System Configuration41 Rstp Port Configuration interface Trap Configuration Snmp ConfigurationSystem Configuration Community Strings Agent ModeUser Profile SNMPV3 ConfigurationContext Table Group Table 44 Snmp V3 Configuration interfaceMIBview Table Access TableQoS Policy and Priority Type QoS ConfigurationPort Base Priority COS ConfigurationTOS Configuration 19 Igmp types Igmp ConfigurationRing 47 X-ring interface 48 Lldp Configuration interface Lldp ConfigurationSecurity 802.1X/Radius Configuration802.1X/Radius System Configuration 802.1x/Radius-Port Configuration802.1X/Radius-Misc Configuration 50 802.1x/Radius Port Setting interface51 802.1x/Radius Misc Configuration interface MAC Address Table-MAC Filtering MAC Address TableMAC Address Table-Static MAC Address MAC Address Table-All MAC Addresses 53 MAC Filtering interface55 All MAC Address interface MAC Address Table-Multicast Filtering56 Factory Default interface Factory Default57 Save Configuration interface Save Configuration58 System Reboot interface System RebootTroubleshooting Diagnosing LED Indicators Pin Assignment & Wiring Appendix a Pin Assignment & Wiring Figure A.4 DB 9-pin female connector EKI-7657C Manualed1 Compatible SFP Modules Appendix B Compatible SFP Modules