Advantech EKI-7657C user manual SNMPV3 Configuration, Context Table, User Profile

Page 85

A trap manager is a management station that receives the trap messages generated by the switch. If no trap manager is defined, no traps will be issued. Create a trap manager by entering the IP address of the station and a community string. To define a management station as a trap manager, assign an IP address, enter the SNMP community strings, and select the SNMP trap version.

IP Address: Enter the IP address of the trap manager.

Community: Enter the community string.

Trap Version: Select the SNMP trap version type—v1 or v2c.

Click Add .

To remove the community string, select the community string listed in the current managers field and

 

click Remove .

Figure 3.43: Trap Configuration interface

SNMPV3 Configuration

Configure the SNMP V3 function.

Context Table

Configure SNMP v3 context table. Assign the context name of context table. Click name. Click Remove to remove unwanted context name.

Add

to add context

User Profile

Configure SNMP v3 user table.

User ID: Set up the user name.

Authentication Password: Set up the authentication password.

Privacy Password: Set up the private password.

Click

Click

Add to add context name.

Remove to remove unwanted context name.

75

Chapter3

Image 85
Contents EKI-7657C Copyright Acknowledgements Product Warranty 2 years FCC Class a Technical Support and Assistance Declaration of ConformitySafety Instructions Safety Precaution Static Electricity Contents Chapter Commands Level Port Troubleshooting Overview Introduction Dual Power InputSFP Advantage High-Speed TransmissionsEasy Troubleshooting Wide Operating TemperatureFlexible Mounting Advanced ProtectionFeatures Power Specification CommunicationsInterface MechanismCertifications EnvironmentPacking List Safety PrecautionEKI-7657C Manualed1 Installation EKI-7657C LED Definition LED IndicatorsFront View of EKI-7657C Dimensions units mmSide View of EKI-7657C Rear View of EKI-7657C Top View of EKI-7657C Wall mounting MountingDIN-rail Mounting Installation to DIN-rail StepInstallation to DIN-rail Step Connection to a Fiber Optic Network Network ConnectionTransceiver Inserted 11 Remove LC connector 13 Pin Assignment of the Power Connector Power Connection14 Pin Assignment of the Dido Connector Wiring the Digital Inputs/OutputsPage Configuration RS-232 Console ConfigurationCOM Port Properties Setting Command Level Commands LevelSystem Commands Set Commands Set ListCommands Set List System Commands SetPort Commands Set Port Commands SetTrunk Commands Set Trunk Commands SetVlan Commands Set Vlan Commands SetSpanning Tree Commands Set Spanning Tree Commands SetIgmp Commands Set QOS Commands Set10 Mac/Filter Table Commands Set QOS Commands Set10 Mac/Filter Table Commands Set Snmp Commands Set11 Snmp Commands Set 13 802.1x Commands Set Port Mirroring Commands Set12 Port Mirroring Commands Set 13 802.1x Commands Set14 Tftp Commands Set Tftp Commands Set15 SysLog,SMTP,Event Commands Set SystemLog, Smtp and Event16 Sntp Commands Set Sntp Commands Set17 X-ring Commands Set Ring Commands SetWeb Browser Management will not be configuredMain System Information SystemIP Configuration IP ConfigurationDhcp Client-System Configuration Dhcp Server-System configurationDhcp Server-Port and IP Bindings 11 Dhcp Server Client EntriesTFTP-Restore Configuration TFTP-Update FirmwareTFTP-Backup Configuration 14 Tftp Restore ConfigurationSystem Event Log-SMTP Configuration System Event Log-Syslog ConfigurationSystem Event Log-Event Configuration 17 Smtp ConfigurationFault Relay Alarm 18 Event Configuration19 Fault Relay Alarm 18 UTC Timezone Sntp Configuration20 Sntp Configuration 21 IP Security IP Security22 User Authentication User AuthenticationDigital Input Digital Input/OutputDigital Output 23 Digital Input/Output interface Port Statistics Port25 Port Control Port ControlPort Trunk Aggregator settingAggregator Information 26 2 work ports with Lacp enabledPassive State Activity30 State Activity 31 Port Mirroring Port Mirroring32 Rate Limiting Rate LimitingVlan configuration Port-based Vlan Vlan configurationProtocol 34 Port based mode 35 Port based mode-Add interface 802.1Q Vlan 802.1Q ConfigurationGroup Configuration 37 802.1Q Vlan ConfigurationRapid Spanning Tree 38 Edit Group Configuration interfacePage RSTP-Port Configuration RSTP-System Configuration41 Rstp Port Configuration interface System Configuration Community Strings Snmp ConfigurationAgent Mode Trap ConfigurationContext Table SNMPV3 ConfigurationUser Profile Group Table 44 Snmp V3 Configuration interfaceMIBview Table Access TableQoS Policy and Priority Type QoS ConfigurationTOS Configuration COS ConfigurationPort Base Priority 19 Igmp types Igmp ConfigurationRing 47 X-ring interface 48 Lldp Configuration interface Lldp Configuration802.1X/Radius System Configuration 802.1X/Radius Configuration802.1x/Radius-Port Configuration Security802.1X/Radius-Misc Configuration 50 802.1x/Radius Port Setting interface51 802.1x/Radius Misc Configuration interface MAC Address Table-Static MAC Address MAC Address TableMAC Address Table-MAC Filtering MAC Address Table-All MAC Addresses 53 MAC Filtering interface55 All MAC Address interface MAC Address Table-Multicast Filtering56 Factory Default interface Factory Default57 Save Configuration interface Save Configuration58 System Reboot interface System RebootTroubleshooting Diagnosing LED Indicators Pin Assignment & Wiring Appendix a Pin Assignment & Wiring Figure A.4 DB 9-pin female connector EKI-7657C Manualed1 Compatible SFP Modules Appendix B Compatible SFP Modules