3Com 3CR17661-91, 3CR17662-91, 3CR17660-91 manual Regulatory Notices

Page 103

REGULATORY NOTICES

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

 

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

 

interference when the equipment is operated in a commercial environment. This equipment generates, uses

 

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

 

may cause harmful interference to radio communications. Operation of this equipment in a residential area is

 

likely to cause harmful interference to radio communications, in which case the user will be required to

 

correct the interference at their own expense.

 

 

INFORMATION TO THE USER

If this equipment does cause interference to radio or television reception, which can be determined by

 

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

 

the following measures:

 

Reorient the receiving antenna.

 

Relocate the equipment with respect to the receiver.

 

Move the equipment away from the receiver.

 

Plug the equipment into a different outlet so that equipment and receiver are on different branch circuits.

 

If necessary, the user should consult the dealer or an experienced radio/television technician for additional

 

suggestions. The user may find the following booklet prepared by the Federal Communications Commission

 

helpful:

 

How to Identify and Resolve Radio-TV Interference Problems

 

This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No.

 

004-000-00345-4.

 

In order to meet FCC emissions limits, this equipment must be used only with cables which comply with IEEE

 

802.3.

 

 

ICES STATEMENT

This Class A digital apparatus complies with Canadian ICES-003.

 

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

 

 

CE STATEMENT (EUROPE)

This product complies with the European Low Voltage Directive 73/23/EEC and EMC Directive 89/336/EEC as

 

amended by European Directive 93/68/EEC.

 

Warning: This is a class A product. In a domestic environment this product may cause radio interference in

 

which case the user may be required to take adequate measures.

 

A copy of the signed Declaration of Conformity can be downloaded from the Product Support web page for

 

the Switch 4200G Family (3CR17660-91, 3CR17661-91, 3CR17662-91) at http://www.3com.com.

 

Also available at http://support.3com.com/doc/SWITCH_4200G_EU_DOC.pdf

 

 

VCCI STATEMENT

 

Image 103
Contents 3Com Switch 4200G Family United States Government Legend 3Com Corporation Campus Drive MarlboroughPage Page Contents Installing the Switch Problem Solving PIN -OUTS About this Guide Icon Description ConventionsConvention Description Documentation RelatedDocumentation Pddtechpubscomments@3com.com CommentsIntroducing Hardware Features Switch 4200G About the Switch 4200GCommander Switch 4200G-Front ViewSwitch 4200G 48-Port-front view Status Display Display Mode LED Color DescriptionColor Indicates Mode LED10/100/1000BASE-T Port LEDs Slots Rear View Detail1000BASE-X Port SFP Port LEDs Configuration Save Feature Switch 4200G Automatic IP ConfigurationDuplex Mode Rmon AlarmInstalling the Switch Choosing a Suitable Package ContentsSite Inch racks To rack-mount your SwitchFront of the Switch, as shown in Figure Rack-mountingFitting a Bracket for Rack-Mounting Repeat and for the other side of the SwitchSequence Power-upPowered-up and ready for operation Switch 4200GSFP Operation LEDs on page 54 for a list of suggested solutionsSFP port Inserting an SFP Transceiver Remove the plastic protective cover if fittedTransceiver Your SwitchChoosing Correct CablesChoosing the Correct Cables Installing the Switch Setting UP for Management Command Line Interface Management Methods of Managing a SwitchRefer to Setting Up Command Line Interface Management on User View There are two main views in the CLISystem View Overview Setting UpSnmp Automatic IP Configuration using Dhcp Manual IP ConfigurationManually Configuring IP Information Prerequisites Connecting the Workstation to the SwitchSetting Up the Switch with IP Information Enter interface vlan 1 and Enter Enter the system-viewcommand and EnterWith a Network Using the Web Interface Using Command Line Interface using Telnet Enter the default gateway for the Switch Viewing Automatically Configured IP InformationUsing 3Com Network Director Viewing IP Information using the Console Port Interface Management Command LineSSH Setting Up Command Line Interface Management usingInterface Setting Up WebChoosing a Browser Windows Red Hat Over the Network2000 Windows XP Server Setting Up Snmp Management V1 or User Default Access Level Name Password Default UsersSetting UP for Management Problem Solving Indicated by LEDs Solving ProblemsSolving Hardware ProblemsUnit fails, no Snmp fan failure message is received Error message indicating that the SFP transceiver is faultyIP Addressing Solving Communication ProblemsHow do you obtain a registered IP Address? Problem Solving Upgrading Software File list similar to the following is displayed To back up the bootrom file on your Switch, enter To back up the application file on your Switch, enterIf the recycle-bin is empty the following is displayed Command Line Interface Switch Setup 4200G ping aaa.aaa.aaa.aaa Via network portTo download the web management file, enter Type y when promptedTo install the new application code, enter To install the new web management code, enterEnter y to display the following message Following information is displayedFollowed by a password prompt Bootrom InterfaceUpgrading from S3t03010024.zip 3comoscfg.def 3comoscfg.cfg s3t030100s56.app Enter your choice0-3 Select option 3 to display the following Select option 2 to display the followingUpgrading BootromUsing FTP Using TftpUsing XModem Ccccccccccccccccccccccccccccc Upgrading Software Safety Information This must be approved for the country where it is used Power Cord Set-Japan Important Safety InformationImportant Safety Information ’information de Sécurité Importante Schko Dispositif Laser De Classe Vorsicht Das Gerät muß geerdet sein Wichtige SicherheitsinformationenInformación de Seguridad Importante Schuko Importanti Informazioni di Sicurezza Stati Uniti e Ważne informacje o zabezpieczeniach Ważne informacje o zabezpieczeniach Ostrzeżenie Porty światłowodowe-bezpieczeństwo PIN-OUTS 10/100 and 1000BASE-T RJ-45 connections Ethernet Port RJ-45 Pin AssignmentsPin Number 10/100 1000 Ethernet Port RJ-45 Pin Assignments Appendix B PIN-OUTS Switch 4200G 12-Port Switch 4200G 24-Port Switch 4200G 48-Port Appendix C Technical Specifications Purchase ServicesRegister Your ProductDownloads Access SoftwareTroubleshoot OnlineContact Us Latin America Telephone Technical Support and Repair Country Telephone NumberUS and Canada Telephone Technical Support and Repair Numbers IndexSFP Regulatory Notices