3Com 3CR17660-91 manual Rack-mounting, Inch racks, To rack-mount your Switch, Facing towards you

Page 23

Rack-mounting 23

■ Water or moisture cannot enter the case of the Switch.

■ Air flow is not restricted around the Switch or through the vents in the side of the Switch. 3Com recommends that you provide a minimum of 25mm (1in.) clearance.

■ Air temperature around the Switch does not exceed 40 °C (104 °F).

If the Switch is installed in a 19-inch rack or closed assembly its local air temperature may be greater than room ambient temperature.

■ The air is as free from dust as possible.

■ The unit is installed in a clean, air conditioned environment.

■ No more than four Switch units are placed on top of one another, if the units are free-standing.

	■ The Switch is situated away from sources of conductive (electrical)
	dust, for example laser printers.
	■ The AC supply used by the Switch is separate to that used by units
	that generate high levels of AC noise, for example air conditioning
	units and laser printers.

Rack-mounting	The Switch 4200G is 1 rack unit (1U) high and will fit in most standard
	19-inch racks.
	CAUTION: Disconnect all cables from the Switch before continuing.
	Remove all self adhesive pads from the underside of the Switch if they
	have been fitted.
	To rack-mount your Switch:
	1 Place the Switch the right way up on a hard flat surface, with the front
	facing towards you.
	2 Locate a mounting bracket over the mounting holes on one side of the
	front of the Switch, as shown in Figure 5.

You can also rack mount your Switch using the mounting holes at the rear of the Switch.

Image 23

Contents

3Com Switch 4200G Family United States Government Legend 3Com Corporation Campus Drive MarlboroughPage Page Contents Installing the Switch Problem Solving PIN -OUTS About this Guide Convention Description ConventionsIcon Description Documentation RelatedDocumentation Pddtechpubscomments@3com.com CommentsIntroducing Hardware Features Switch 4200G About the Switch 4200GCommander Switch 4200G-Front ViewSwitch 4200G 48-Port-front view Status Display Display Mode LED Color Description10/100/1000BASE-T Port LEDs Mode LEDColor Indicates 1000BASE-X Port SFP Port LEDs Rear View DetailSlots Configuration Save Feature Switch 4200G Automatic IP Configuration Duplex Mode Rmon AlarmInstalling the Switch Site Package ContentsChoosing a Suitable Inch racks To rack-mount your SwitchFront of the Switch, as shown in Figure Rack-mountingFitting a Bracket for Rack-Mounting Repeat and for the other side of the SwitchSequence Power-upPowered-up and ready for operation Switch 4200GSFP port LEDs on page 54 for a list of suggested solutionsSFP Operation Inserting an SFP Transceiver Remove the plastic protective cover if fittedTransceiver Your SwitchChoosing Correct CablesChoosing the Correct Cables Installing the Switch Setting UP for Management Refer to Setting Up Command Line Interface Management on Methods of Managing a SwitchCommand Line Interface Management System View There are two main views in the CLIUser View Overview Setting UpSnmp Automatic IP Configuration using Dhcp Manual IP ConfigurationManually Configuring IP Information Prerequisites Connecting the Workstation to the SwitchSetting Up the Switch with IP Information Enter interface vlan 1 and Enter Enter the system-viewcommand and EnterWith a Network Using the Web Interface Using Command Line Interface using Telnet Using 3Com Network Director Viewing Automatically Configured IP InformationEnter the default gateway for the Switch Viewing IP Information using the Console Port Interface Management Command LineSSH Setting Up Command Line Interface Management usingChoosing a Browser Setting Up WebInterface 2000 Windows XP Server Over the NetworkWindows Red Hat Setting Up Snmp Management V1 or User Default Access Level Name Password Default UsersSetting UP for Management Problem Solving Indicated by LEDs Solving ProblemsSolving Hardware ProblemsUnit fails, no Snmp fan failure message is received Error message indicating that the SFP transceiver is faultyHow do you obtain a registered IP Address? Solving Communication ProblemsIP Addressing Problem Solving Upgrading Software File list similar to the following is displayed If the recycle-bin is empty the following is displayed To back up the application file on your Switch, enterTo back up the bootrom file on your Switch, enter Command Line Interface Switch Setup 4200G ping aaa.aaa.aaa.aaa Via network portTo download the web management file, enter Type y when promptedTo install the new application code, enter To install the new web management code, enterEnter y to display the following message Following information is displayedUpgrading from Bootrom InterfaceFollowed by a password prompt S3t03010024.zip 3comoscfg.def 3comoscfg.cfg s3t030100s56.app Enter your choice0-3 Select option 3 to display the following Select option 2 to display the followingUpgrading BootromUsing FTP Using TftpUsing XModem Ccccccccccccccccccccccccccccc Upgrading Software Safety Information This must be approved for the country where it is used Power Cord Set-Japan Important Safety InformationImportant Safety Information ’information de Sécurité Importante Schko Dispositif Laser De Classe Vorsicht Das Gerät muß geerdet sein Wichtige SicherheitsinformationenInformación de Seguridad Importante Schuko Importanti Informazioni di Sicurezza Stati Uniti e Ważne informacje o zabezpieczeniach Ważne informacje o zabezpieczeniach Ostrzeżenie Porty światłowodowe-bezpieczeństwo PIN-OUTS Pin Number 10/100 1000 Ethernet Port RJ-45 Pin Assignments10/100 and 1000BASE-T RJ-45 connections Ethernet Port RJ-45 Pin Assignments Appendix B PIN-OUTS Switch 4200G 12-Port Switch 4200G 24-Port Switch 4200G 48-Port Appendix C Technical Specifications Purchase ServicesRegister Your ProductDownloads Access SoftwareTroubleshoot OnlineContact Us US and Canada Telephone Technical Support and Repair Country Telephone NumberLatin America Telephone Technical Support and Repair Numbers IndexSFP Regulatory Notices