SUPER MICRO Computer SCF418IL-R1K62BP, SCF418IF-R1K62BP Power Disconnection Warning, 電源切断の警告

Page 17

SUPERSERVER "servername" User's Manual

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다.

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the chassis interior to install or remove system components.

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り 外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen.

2-6

Image 17
Contents Super SCF418 Chassis Manual About This Manual PrefaceIntroduction Manual OrganizationPreface Table of Contents Chassis Setup and Maintenance Rack Installation Overview Chapter IntroductionShipping List Part NumbersEurope Contacting SupermicroReturning Merchandise for Service About Standardized Warning Statements Chapter Standardized Warning Statements for AC Systemsהרהזא תורהצה ןונקת Bewaar Deze Instructies 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 Installation InstructionsCircuit Breaker 電源切断の警告 Power Disconnection Warningםיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל 機器の設置 Equipment Installationアクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 Restricted Area電池の取り扱い Battery HandlingPage הדיחיה תא Redundant Power Suppliesバックプレーンの電圧 Backplane Voltage地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 Comply with Local and National Electrical Codes製品の廃棄 Product Disposalファン・ホットスワップの警告 Hot Swap Fan Warning當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 電源コードとACアダプター Power Cable and AC AdapterPage Page Components Chapter Chassis ComponentsWhere to get Replacement Components Chassis Control Panel Chapter System InterfaceControl Panel LEDs Control Panel ButtonsSAS/SATA Drives Drive Carrier LEDsSCF418 Chassis Manual Removing the Power Cord Chapter Chassis Setup and MaintenanceRemoving Power Cords Node Node LocationsNode Removing the Cover from the Node Removing Nodes from the ChassisRemoving a Node Removing the Node CoverSCF418BC-R1K62BP Node Layout Node ConfigurationsOverview of the Node SCF418IL-R1K62BP Node Layout SCF418IF-R1K62BP Node LayoutHard Drives and the Corresponding Motherboards Nodes and Associated Hard DrivesControls two fixed 3.5 HDDs E1-E2 Removing 2.5 Hard Drive Carriers from the Node Installing and Removing Hard DrivesInstalling and Removing 2.5 Hard Drives 2.5 Hard Drive Carrier Installing a 2.5 Drive into the Hard Drive Carrier11 Installing a 2.5 Hard Drive in the Drive Carrier Removing 3.5 Fixed Hard Drives from the Node Installing and Removing 3.5 Fixed Hard Drives14 Installing a 3.5 Fixed Hard Drive in the Node Removing the Backplane from the Chassis Removing and Installing the BackplaneRemoving the Backplane Lift the backplane up and out of the node Installing the Backplane into the Chassis Installing the BackplaneCompatible Motherboards Permanent and Optional Standoffs Installing the MotherboardInstalling the Motherboard SCF418 Pcie Slot Configurations Installing Expansion Cards19 I/O Shield Configuration Installing Rear Low-profile Expansion CardsAssembling the Pcie Slot Bracket Assembly Assembling the Pcie Slot Bracket AssemblyInstalling the Pcie Slot Bracket Assembly Installing the Pcie Slot Bracket Assembly Into the NodeInstalling the Micro LP Card Assembly Installing Rear Micro LP CardsInstalling Front Low-profile Expansion Cards 24 Assembling the Pcie Slot Bracket and Riser Card Bracket Mounting Screws Air Shrouds Installing Air ShroudsInstalling an Air Shroud Removing and Installing Internal System Fans Removing and Installing System FansInstalling Internal System Fans Removing Internal System FansRemoving a Rear Exhaust Fan Removing and Installing External System FansInstalling a Rear Exhaust Fan Changing the Power Supply Replacing the Power SuppliesPower Supply Replacement SCF418 Chassis Manual Preparing for Setup Chapter Rack InstallationChoosing a Setup Location Unpacking the SystemGeneral Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Adjusting the RailsRack Mounting Instructions Installing the Rails Installing the Rails on a RackInstalling the Chassis into a Rack Chassis InstallationAppendix a SCF418 Power Supply Specifications SCF418 Chassis Manual General Safety Guidelines Appendix B BPN-SAS-F418-B6 Backplane SpecificationsESD Safety Guidelines Introduction to the BPN-SAS-F418-B6 Backplane An Important Note to UsersFigure B-1 Front Connectors Front ConnectorsBackplane Main Power Connectors Front Connector and Pin DefinitionsD24 Rear Connectors and LED IndicatorsSCF418 Chassis Manual Appendix C BPN-SAS-F418B2R Backplane Specifications Introduction to the BPN-SAS-F418-B2R Backplane BPN-SAS-F418-B2R Backplane Main Power Connector BAR Code