SUPER MICRO Computer SCF418C-R1K62BP, SCF418IF-R1K62BP Removing and Installing System Fans

Page 64

Chapter 5: Chassis Setup and Maintenance

5-13 Removing and Installing System Fans

Removing and Installing Internal System Fans

Removing Internal System Fans

1.Power down the system and remove the power cords from the rear of the power supplies as described in Section 5-2. Remove the node from the chassis as described in Section 5-4 and remove the cover from the node as described in Section 5-5.

2.Disconnect the wiring to all three fans.

3.Remove the four screws securing the fan tray to the floor of the node and set them aside for future use.

4.Lift the fan tray up and out of the node.

5.Push upward on the underside of the failed fan to remove it from the fan tray.

Installing Internal System Fans

1.Insert the replacement fan into the fan tray, making certain that the fan is fac- ing in the same direction as the other fans in the fan tray.

2.Place the fan tray in the node.

3.Secure the fan tray to the floor of the node with the four screws previously set aside.

4.Reconnect the wiring to the fans.

Figure 5-28:

Figure 5-29:

Removing the Fan Tray

Removing the Fan from the Fan Tray

(Your node may differ slightly from the one shown in this illustration)

5-27

Image 64
Contents Super SCF418 Chassis Manual Preface About This ManualManual Organization IntroductionPreface Table of Contents Chassis Setup and Maintenance Rack Installation Chapter Introduction OverviewShipping List Part NumbersContacting Supermicro EuropeReturning Merchandise for Service Chapter Standardized Warning Statements for AC Systems About Standardized Warning Statementsהרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning 電源切断の警告םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置Restricted Area アクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。Battery Handling 電池の取り扱いPage Redundant Power Supplies הדיחיה תאBackplane Voltage バックプレーンの電圧Comply with Local and National Electrical Codes 地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。Product Disposal 製品の廃棄Hot Swap Fan Warning ファン・ホットスワップの警告當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Power Cable and AC Adapter 電源コードとACアダプターPage Page Chapter Chassis Components ComponentsWhere to get Replacement Components Chapter System Interface Chassis Control PanelControl Panel Buttons Control Panel LEDsDrive Carrier LEDs SAS/SATA DrivesSCF418 Chassis Manual Removing Power Cords Chapter Chassis Setup and MaintenanceRemoving the Power Cord Node Node LocationsNode Removing Nodes from the Chassis Removing the Cover from the NodeRemoving a Node Removing the Node CoverOverview of the Node Node ConfigurationsSCF418BC-R1K62BP Node Layout SCF418IF-R1K62BP Node Layout SCF418IL-R1K62BP Node LayoutNodes and Associated Hard Drives Hard Drives and the Corresponding MotherboardsControls two fixed 3.5 HDDs E1-E2 Installing and Removing 2.5 Hard Drives Installing and Removing Hard DrivesRemoving 2.5 Hard Drive Carriers from the Node Installing a 2.5 Drive into the Hard Drive Carrier 2.5 Hard Drive Carrier11 Installing a 2.5 Hard Drive in the Drive Carrier Installing and Removing 3.5 Fixed Hard Drives Removing 3.5 Fixed Hard Drives from the Node14 Installing a 3.5 Fixed Hard Drive in the Node Removing the Backplane Removing and Installing the BackplaneRemoving the Backplane from the Chassis Lift the backplane up and out of the node Installing the Backplane Installing the Backplane into the ChassisInstalling the Motherboard Compatible Motherboards Permanent and Optional StandoffsInstalling the Motherboard Installing Expansion Cards SCF418 Pcie Slot ConfigurationsInstalling Rear Low-profile Expansion Cards 19 I/O Shield ConfigurationAssembling the Pcie Slot Bracket Assembly Assembling the Pcie Slot Bracket AssemblyInstalling the Pcie Slot Bracket Assembly Into the Node Installing the Pcie Slot Bracket AssemblyInstalling Rear Micro LP Cards Installing the Micro LP Card AssemblyInstalling Front Low-profile Expansion Cards 24 Assembling the Pcie Slot Bracket and Riser Card Bracket Mounting Screws Installing an Air Shroud Installing Air ShroudsAir Shrouds Removing and Installing System Fans Removing and Installing Internal System FansInstalling Internal System Fans Removing Internal System FansInstalling a Rear Exhaust Fan Removing and Installing External System FansRemoving a Rear Exhaust Fan Power Supply Replacement Replacing the Power SuppliesChanging the Power Supply SCF418 Chassis Manual Chapter Rack Installation Preparing for SetupChoosing a Setup Location Unpacking the SystemRack Precautions General Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsRack Mounting Instructions Adjusting the RailsIdentifying the Sections of the Rack Rails Installing the Rails on a Rack Installing the RailsChassis Installation Installing the Chassis into a RackAppendix a SCF418 Power Supply Specifications SCF418 Chassis Manual ESD Safety Guidelines Appendix B BPN-SAS-F418-B6 Backplane SpecificationsGeneral Safety Guidelines An Important Note to Users Introduction to the BPN-SAS-F418-B6 BackplaneFront Connectors Figure B-1 Front ConnectorsFront Connector and Pin Definitions Backplane Main Power ConnectorsRear Connectors and LED Indicators D24SCF418 Chassis Manual Appendix C BPN-SAS-F418B2R Backplane Specifications Introduction to the BPN-SAS-F418-B2R Backplane BPN-SAS-F418-B2R Backplane Main Power Connector BAR Code