SUPER MICRO Computer SCF418IF-R1K62BP, SYSF617R2RT Assembling the Pcie Slot Bracket Assembly

Page 57

SCF418 Chassis Manual

PCIE Slot

Bracket

Expansion

Card Bracket

Riser Card

 

 

Card

Expansion

Mounting

Card

Screws

Figure 5-20: Assembling the PCIE Slot Bracket and Cards

Assembling the PCIE Slot Bracket Assembly

Each node supports one expansion card. This expansion card must be plugged into a riser card, which in turn plugs into the motherboard.

Assembling the PCIE Slot Bracket Assembly

1.Remove the node from the chassis as described in Section 5-2, remove the node from the chassis as described in Section 5-4 and remove the cover from the node as described in Section 5-5.

2.Open the PCIE slot clip and remove the PCIE slot shield. (See the illustration on the previous page)

3.Remove the three mounting screws securing the PCIE slot bracket to the node.

4.Lift the PCIE slot bracket out of the node.

5.Insert the expansion card into the riser card.

6.Secure the riser card to the PCIE slot bracket using the two screws included in the accessory box.

7.Insert the expansion card bracket into the PCIE slot bracket

8.Secure the expansion card bracket ot the PCIE slot bracket using two screws as illustrated.

5-20

Image 57
Contents Super SCF418 Chassis Manual About This Manual PrefaceIntroduction Manual OrganizationPreface Table of Contents Chassis Setup and Maintenance Rack Installation Overview Chapter IntroductionShipping List Part NumbersEurope Contacting SupermicroReturning Merchandise for Service About Standardized Warning Statements Chapter Standardized Warning Statements for AC Systemsהרהזא תורהצה ןונקת Bewaar Deze Instructies 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 Installation InstructionsCircuit Breaker 電源切断の警告 Power Disconnection Warningםיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל 機器の設置 Equipment Installationアクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 Restricted Area電池の取り扱い Battery HandlingPage הדיחיה תא Redundant Power Suppliesバックプレーンの電圧 Backplane Voltage地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 Comply with Local and National Electrical Codes製品の廃棄 Product Disposalファン・ホットスワップの警告 Hot Swap Fan Warning當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 電源コードとACアダプター Power Cable and AC AdapterPage Page Components Chapter Chassis ComponentsWhere to get Replacement Components Chassis Control Panel Chapter System InterfaceControl Panel LEDs Control Panel ButtonsSAS/SATA Drives Drive Carrier LEDsSCF418 Chassis Manual Chapter Chassis Setup and Maintenance Removing Power CordsRemoving the Power Cord Node Locations NodeNode Removing the Cover from the Node Removing Nodes from the ChassisRemoving a Node Removing the Node CoverNode Configurations Overview of the NodeSCF418BC-R1K62BP Node Layout SCF418IL-R1K62BP Node Layout SCF418IF-R1K62BP Node LayoutHard Drives and the Corresponding Motherboards Nodes and Associated Hard DrivesControls two fixed 3.5 HDDs E1-E2 Installing and Removing Hard Drives Installing and Removing 2.5 Hard DrivesRemoving 2.5 Hard Drive Carriers from the Node 2.5 Hard Drive Carrier Installing a 2.5 Drive into the Hard Drive Carrier11 Installing a 2.5 Hard Drive in the Drive Carrier Removing 3.5 Fixed Hard Drives from the Node Installing and Removing 3.5 Fixed Hard Drives14 Installing a 3.5 Fixed Hard Drive in the Node Removing and Installing the Backplane Removing the BackplaneRemoving the Backplane from the Chassis Lift the backplane up and out of the node Installing the Backplane into the Chassis Installing the BackplaneCompatible Motherboards Permanent and Optional Standoffs Installing the MotherboardInstalling the Motherboard SCF418 Pcie Slot Configurations Installing Expansion Cards19 I/O Shield Configuration Installing Rear Low-profile Expansion CardsAssembling the Pcie Slot Bracket Assembly Assembling the Pcie Slot Bracket AssemblyInstalling the Pcie Slot Bracket Assembly Installing the Pcie Slot Bracket Assembly Into the NodeInstalling the Micro LP Card Assembly Installing Rear Micro LP CardsInstalling Front Low-profile Expansion Cards 24 Assembling the Pcie Slot Bracket and Riser Card Bracket Mounting Screws Installing Air Shrouds Installing an Air ShroudAir Shrouds Removing and Installing Internal System Fans Removing and Installing System FansInstalling Internal System Fans Removing Internal System FansRemoving and Installing External System Fans Installing a Rear Exhaust FanRemoving a Rear Exhaust Fan Replacing the Power Supplies Power Supply ReplacementChanging the Power Supply SCF418 Chassis Manual Preparing for Setup Chapter Rack InstallationChoosing a Setup Location Unpacking the SystemGeneral Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureAdjusting the Rails Rack Mounting InstructionsIdentifying the Sections of the Rack Rails Installing the Rails Installing the Rails on a RackInstalling the Chassis into a Rack Chassis InstallationAppendix a SCF418 Power Supply Specifications SCF418 Chassis Manual Appendix B BPN-SAS-F418-B6 Backplane Specifications ESD Safety GuidelinesGeneral Safety Guidelines Introduction to the BPN-SAS-F418-B6 Backplane An Important Note to UsersFigure B-1 Front Connectors Front ConnectorsBackplane Main Power Connectors Front Connector and Pin DefinitionsD24 Rear Connectors and LED IndicatorsSCF418 Chassis Manual Appendix C BPN-SAS-F418B2R Backplane Specifications Introduction to the BPN-SAS-F418-B2R Backplane BPN-SAS-F418-B2R Backplane Main Power Connector BAR Code