SUPER MICRO Computer SCF418, SYSF617R2RT Chassis Installation, Installing the Chassis into a Rack

Page 73

SCF418 Chassis Manual

Figure 6-4: Installing into a Rack

Note: figures are for illustrative purposes only. Always install servers into racks from the bottom up.

Chassis Installation

Installing the Chassis into a Rack

1.Confirm that the rails are correctly installed on the rack.

2.Align the bottom of the chassis with the bottom of the rails.

3.Insert the chassis into the rails, keeping the pressure even on both sides, pushing the chassis into the rack until it clicks into the locked position.

4.Secure the chassis handles to the front of the rack.

Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.

6-6

Image 73
Contents Super SCF418 Chassis Manual About This Manual PrefaceIntroduction Manual OrganizationPreface Table of Contents Chassis Setup and Maintenance Rack Installation Overview Chapter IntroductionShipping List Part NumbersEurope Contacting SupermicroReturning Merchandise for Service About Standardized Warning Statements Chapter Standardized Warning Statements for AC Systemsהרהזא תורהצה ןונקת Bewaar Deze Instructies 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 Installation InstructionsCircuit Breaker 電源切断の警告 Power Disconnection Warningםיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל 機器の設置 Equipment Installationアクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 Restricted Area電池の取り扱い Battery HandlingPage הדיחיה תא Redundant Power Suppliesバックプレーンの電圧 Backplane Voltage地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 Comply with Local and National Electrical Codes製品の廃棄 Product Disposalファン・ホットスワップの警告 Hot Swap Fan Warning當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 電源コードとACアダプター Power Cable and AC AdapterPage Page Components Chapter Chassis ComponentsWhere to get Replacement Components Chassis Control Panel Chapter System InterfaceControl Panel LEDs Control Panel ButtonsSAS/SATA Drives Drive Carrier LEDsSCF418 Chassis Manual Removing Power Cords Chapter Chassis Setup and MaintenanceRemoving the Power Cord Node Node LocationsNode Removing the Cover from the Node Removing Nodes from the ChassisRemoving a Node Removing the Node CoverOverview of the Node Node ConfigurationsSCF418BC-R1K62BP Node Layout SCF418IL-R1K62BP Node Layout SCF418IF-R1K62BP Node LayoutHard Drives and the Corresponding Motherboards Nodes and Associated Hard DrivesControls two fixed 3.5 HDDs E1-E2 Installing and Removing 2.5 Hard Drives Installing and Removing Hard DrivesRemoving 2.5 Hard Drive Carriers from the Node 2.5 Hard Drive Carrier Installing a 2.5 Drive into the Hard Drive Carrier11 Installing a 2.5 Hard Drive in the Drive Carrier Removing 3.5 Fixed Hard Drives from the Node Installing and Removing 3.5 Fixed Hard Drives14 Installing a 3.5 Fixed Hard Drive in the Node Removing the Backplane Removing and Installing the BackplaneRemoving the Backplane from the Chassis Lift the backplane up and out of the node Installing the Backplane into the Chassis Installing the BackplaneCompatible Motherboards Permanent and Optional Standoffs Installing the MotherboardInstalling the Motherboard SCF418 Pcie Slot Configurations Installing Expansion Cards19 I/O Shield Configuration Installing Rear Low-profile Expansion CardsAssembling the Pcie Slot Bracket Assembly Assembling the Pcie Slot Bracket AssemblyInstalling the Pcie Slot Bracket Assembly Installing the Pcie Slot Bracket Assembly Into the NodeInstalling the Micro LP Card Assembly Installing Rear Micro LP CardsInstalling Front Low-profile Expansion Cards 24 Assembling the Pcie Slot Bracket and Riser Card Bracket Mounting Screws Installing an Air Shroud Installing Air ShroudsAir Shrouds Removing and Installing Internal System Fans Removing and Installing System FansInstalling Internal System Fans Removing Internal System FansInstalling a Rear Exhaust Fan Removing and Installing External System FansRemoving a Rear Exhaust Fan Power Supply Replacement Replacing the Power SuppliesChanging the Power Supply SCF418 Chassis Manual Preparing for Setup Chapter Rack InstallationChoosing a Setup Location Unpacking the SystemGeneral Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureRack Mounting Instructions Adjusting the RailsIdentifying the Sections of the Rack Rails Installing the Rails Installing the Rails on a RackInstalling the Chassis into a Rack Chassis InstallationAppendix a SCF418 Power Supply Specifications SCF418 Chassis Manual ESD Safety Guidelines Appendix B BPN-SAS-F418-B6 Backplane SpecificationsGeneral Safety Guidelines Introduction to the BPN-SAS-F418-B6 Backplane An Important Note to UsersFigure B-1 Front Connectors Front ConnectorsBackplane Main Power Connectors Front Connector and Pin DefinitionsD24 Rear Connectors and LED IndicatorsSCF418 Chassis Manual Appendix C BPN-SAS-F418B2R Backplane Specifications Introduction to the BPN-SAS-F418-B2R Backplane BPN-SAS-F418-B2R Backplane Main Power Connector BAR Code