SUPER MICRO Computer X8SIA-F user manual Appendix a Post Error Beep Codes

Page 8

 

Table of Contents

 

 

Appendix A POST Error Beep Codes

 

Recoverable POST Error Beep Codes

A-1

Appendix B Software Installation Instructions

 

B-1

Installing Drivers

B-1

B-2

Configuring Supero Doctor III

B-2

Appendix C - BIOS Recovery

 

C-1

Recovery Process from a USB Device/Drive (Recommended Method)

C-1

C-2

Recovery Process from an IDE/SATA ATAPI Disc Drive

C-2

Page 7 Page 9
Image 8
Page 7 Page 9
Contents X8SIA X8SIA-F Page About This Motherboard Manual Organization Conventions Used in the ManualContacting Supermicro HeadquartersEurope Asia-PacificTable of Contents Vii Troubleshooting IntroductionAppendix a Post Error Beep Codes Quick-Start Guide Install the Memory Modules Install the Motherboard Install Internal Peripherals Checklist OverviewMotherboard X8SIA-F Image Motherboard Layout X8SIA-F Shown CPU411 401 391 381 111 121 131 141 X8SIA/X8SIA-F Quick ReferenceNumber Connector Description 42,41,37,32,11Description Color/State Status Number Jumper Description DefaultNumber Motherboard Features Power Configuration DimensionsSerial COM Ports Super I/OBlock Diagram X8SIA/X8SIA-F System Block DiagramIntel 3420 Chipset Features Chipset OverviewPower Configuration Settings PC Health MonitoringPower Supply Slow Blinking LED for Suspend-State IndicatorBios Support for USB Keyboard Main Switch Override MechanismSuper I/O ISCSI SupportOverview of the Nuvoton BMC Controller Unpacking PrecautionsStatic-Sensitive Devices Processor and Heatsink Installation Installing the LGA1156 ProcessorPage Page Installing a Passive CPU Heatsink Removing the Heatsink Installing an Active Fan CPU Heatsink Page Active Heatsink Removal Memory Support How to Install DIMMsSystem Memory Populated Any combination Per Channel Memory Population GuidelinesDDR3 ECC Registered Rdimm Memory Support Registered 1066 Single Rank, Dual Installing and Removing DIMMs To RemovePossible System Memory Allocation & Availability Location of Mounting Holes Motherboard InstallationTools Needed Installation Instructions Connectors/IO Ports Back Panel Connectors and IO PortsATX PS/2 Keyboard and PS/2 Mouse Ports MouseKeyboard Keyboard Purple Mouse GreenUniversal Serial Bus USB For pin definitionsEthernet Ports NC No Connection LAN1 LAN2 Ipmi Dedicated LANSerial Ports COM1 COM2 HeaderVideo Connector VGAJF1 Header Pins Front Control PanelPower LED Front Control Panel Pin DefinitionsOverheat OH/Fan Fail OH/Fan FailPower Fail LED Reset ButtonPower Button Power Fail LED Reset Button PWR ButtonRequired Pin ATX Main PWR Pin Processor PWR Connecting CablesATX Main PWR & CPU PWR Connectors Fan1 Fan2 CPU Fan Fan3 Fan4 Fan5 Chassis Intrusion Fan HeadersChassis Intrusion Internal Buzzer Speaker Header Internal BuzzerSpeaker Onboard Power LED Power Supply I2C ConnectorSgpio 0/1 Headers Sata DOM PowerSata DOM Power Jwor Wake On Ring Jwol Wake On LAN Wake-On-RingWake-On-LAN Ipmb Jumper Settings LAN Port Enable/DisableLAN Port 1 Enable B. LAN Port 2 Enable Explanation of JumpersClear Cmos JI2C1 JI2C2 PCI Slot SMB EnableCmos Clear BP USB 0/1 Wake-up BMC Jumper USB Wake-UpBMC Jumper X8SIA-F Only VGA Enable VGA EnableOnboard Indicators LAN LEDsIpmi Dedicated LAN X8SIA-F Only LAN Port 1 B. LAN PortIpmi Heartbeat LED X8SIA-F Only Onboard PWR LED Ipmi Heartbeat LEDSata and Floppy Drive Connections Sata ConnectionsFloppy Connector FloppyPage Troubleshooting Procedures Before Power OnNo Power No VideoLost System Setup Configuration Technical Support ProceduresMemory Errors Question What type of memory does my motherboard support? Frequently Asked QuestionsQuestion How do I update my BIOS? Question Whats on the CD that came with my motherboard? Troubleshooting Battery Installation Battery Removal and InstallationBattery Removal Returning Merchandise for Service Page Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup UtilitySystem Memory System Time/System DateProcessor Advanced Setup Configurations BOOT FeatureProcessor & Clock Options MPS and Acpi Madt Ordering Hardware Prefetcher Available when supported by the CPUClock Spread Spectrum State package limit setting Active Processor CoresIntel Eist Technology C1E SupportSATA / Floppy Configuration Advanced Chipset ControlSATA#1 Configuration Configure Sata asIDE Detect Timeout sec LBA/Large ModeBlock Multi-Sector Transfer PIO ModeDMA Mode PCI/PnP Configuration A.R.T. For Hard disk drivesBit Data Transfer Clear NvramSuper IO Device Configuration Remote Access Configuration Hardware Health Configuration Page ACPI Configuration High Performance Event TimerFan1 ~ Fan5 Reading Fan Speed Control ModesIPMI Configuration X8SIA-F Only Clear BMC System Event Log Set LAN ConfigurationView BMC System Event Log Event Log Configuration Intel TXT LT ConfigurationSecurity Settings Supervisor PasswordUser Password Change Supervisor PasswordBoot Sector Virus Protection Boot SettingsBoot Device Priority Retry Boot Devices Exit OptionsHard Disk Drives Removable DrivesLoad Optimal Defaults Load Fail-Safe DefaultsSave Changes and Exit Discard Changes and ExitX8SIA/X8SIA-F Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Installing Drivers Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Recovery Process from a USB Device/Drive Recommended Method Part 1 Boot Sector Recovery ProcessRecovery Process from an IDE/SATA Atapi Disc Drive Part 2 Bios Reprogramming Re-Flashing
Top Page Image Contents