SUPER MICRO Computer FAN0103L4 Removing the Chassis Side and Top Covers, Removing the Side Cover

Page 22

SC743 Chassis Manual

4-2 Removing the Chassis Side and Top Covers

Disconnecting the Chassis from the Power Source

1.Turn off all peripheral devices and turn off the power supply to the SC743.

2.Disconnect the AC power cords from the system.

3.Disconnect all cables and label the cables for easy identification.

!

Warning: Use a grounded wrist strap designed to prevent static discharge when handling compo- nents.

!

Removing the Side Cover

Removing the Side Cover of the Chassis

1.Disconnect the chassis from any power source as described above.

2.Press the release tab to unlock the cover.

3.The release tab will pop open as shown.

4.Slide the cover back and off of the chassis.

14

13

12

Figure 4-1: Removing the Side Cover

4-2

Image 22

Contents Super SC743 Chassis Manual Preface About This ManualManual Organization IntroductionTable of Contents Appendix B Power Supply Specifications Shipping List Chapter IntroductionOverview Part NumbersWhere to get Replacement Components Europe Contacting SupermicroHeadquarters Asia-PacificReturning Merchandise for Service Chapter System Safety Preparing for SetupElectrical Safety Precautions System Safety Page Components Power SupplyChapter Chassis Components ChassisWhere to get Replacement Components Front Control Panel Front Control PanelControl Panel Buttons Control Panel LEDsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Side Cover Disconnecting the Chassis from the Power SourceRemoving the Chassis Side and Top Covers Removing the Side Cover of the ChassisRemoving the Top Cover of the Chassis Removing the Top CoverRelease Tab Accessing and Removing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersInstalling Hard Drive Carriers Installing Hard Drives Installing Hard Drives into the Drive CarriersRemoving the Dummy Drive Installing Fixed Hard Drives in SC743i Series Chassis Models Storage Module Options Configuring the Storage ModuleRemoving the Storage Module Configuring the Storage Module for 5.25 Devices Storage Module Mobile Rack Bracket DevicesStandard Cooling Systems Removing and Replacing the System FansSC743TQ-865B-SQ Cooling System Removing and Replacing Mid-chassis FansRemoving Rear Chassis Fans 10 Removing Rear Chassis FansRemoving the Air Shroud Removing the Air ShroudMotherboard Installation Installing the MotherboardPrior to Installing the Motherboard Installing the Motherboard12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage 465, 500, 665 and 865 Watt Power Supplies Power SupplyInstalling the Power Supply 15 Removing the Interior Chassis Screws on the Power Supply Remove Screws14Watt Power Supply 16 Installing the 760 Watt Power SupplyAccessing the Interior Space 17 Accessing the Interior Backplane/Midplane SpaceInstalling the Driver Installing the Driver Alternative Procedure Select Enclosure Services Device and click NextSC743 Chassis Manual Choosing a Setup Location Chapter Rack InstallationUnpacking the System Rack Precautions General Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsBefore Installing the Chassis Rails Installing the Chassis Rack Mounting RailsInstalling the Inner Chassis Rails Installing the Outer Chassis Rails Middle Rail End Rail End BracketOuter Rail Assemblies Inner Rails Mounting the Chassis into a RackSC743S1 Series Scsi Type Length Appendix a Cables, Screws Other AccessoriesOverview Cables Included with the SC743 Chassis SC743S2 Series Scsi Type Length DescriptionSC743TQ Series SATA/SCSI SC743T Series SAS/SATASC743i Series Type Length Description Power Cable Extenders Number of Pins Length Extending Power CablesFront Panel to the Motherboard Chassis Screws DVD-ROM, CD-ROM, and Floppy DriveAppendix B Power Supply Specifications Power Supply OptionsMFR Rated AC Voltage +5V standby +12V +3.3V R760W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V 865W Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Product FeaturesPacking List Supported Operating SystemsAdditional Information Jumper Settings Front Connectors and JumpersJumper Description Setting Page Jumper Settings and Locations for the CSE-M35T Sata Figure C-2 Jumper LocationsAccessing Hot-Swappable Drives Installation ProceduresInstalling the CSE-M35S Backplane Release ButtonsInstalling a Drive into the Drive Tray Figure C-5 Installing the Drive into the Drive TrayAccessing the Backplane Figure C-6 Accessing the BackplaneSC743 Chassis Manual Appendix D M35TQ Mobile Rack Specificaitons System MonitoringGeneral Safety Guidelines ESD Safety GuidelinesAn Important Note to the User Introduction to the SAS-M35TQ Backplane Figure D-1 Front Connectors Front ConnectorsJtag Connector Front Connectors and Pin DefinitionsMobile Rack Main Power Connectors 5. I2C Connectors7. Sideband Headers Upgrade ConnectorFan Connector Activity LED HeaderFront Jumper Locations and Pin Definitions JP40Jumper Settings Buzzer and Chip Reset Jumper SettingsBuzzer alarm is triggered by the following conditions Fan Jumper Settings Fan Jumper SettingsI2C/SGPIO Settings Jumper I2C and Sgpio Modes and Jumper SettingsI2C Setting Default Rear Connectors and LED Indicators Figure D-6 Rear Connectors and LED IndicatorsDrive Number Rear SAS/SATA ConnectorsRear LED Indicators Hard Drive ActivitySafety Guidelines Preparing for InstallationImportant Safety Guidelines Tools RequiredRelease Button Installation ProceduresInstalling Hard Drives into the Mobile Rack Removing Hard Drives from the Mobile RackInstalling a Hard Drive into the Hard Drive Carrier Dummy Drive Drive CarrierFigure D-10 Installing a Hard Drive SAS/SATA or Scsi Hard Drive Drive TrayConnecting Cables to the Mobile Rack Removing the Exhaust Fan and Connecting SAS/SATA CablesFigure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Additional Optional Installation Information Backplane Screw LocationsAppendix E SAS-743TQ Backplane Specifications An Important Note to Users Introduction to the SAS-743TQ BackplaneFront Connectors Figure E-1 Front Connectors#4. Backplane Main Power Connectors Front Connector and Pin Definitions#1. and 2. Jtag Connector and Upgrade Connectors #3. MG9072 Chip#6. and #7. Sideband Headers #8. and #9. I2C Connectors#10. #17. SAS Ports JP41 JP34Connector Pins Jumper Setting I2C and Sgpio Mode Jumper Settings SAS Port Connections in I2C and Sgpio SettingsState Specification Front LED IndicatorsOH/Drive Fail LED J15 SAS Drive NumberAppendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Connectors and Jumpers Figure F-1 Front ConnectorsFront Connector and Jumper Pin Definitions JP25 Explanation of JumpersJP18 MM2 Front LED Indicator Normal State Indicator StatusRear Connectors Figure F-4 Rear Connectors Rear Sata ConnectorsRear LEDs Appendix F SATA-743 Backplane Specifications