SUPER MICRO Computer FAN0103L4 user manual Installing the Outer Chassis Rails

Page 47

Chapter 5: Rack Installation

Installing the Outer Chassis Rails

1.Locate the two pairs of outer rails. Each pair consists of one middle rail, one end bracket and one end rail as shown.

Middle Rail

End Rail

End Bracket

Figure 5-2: Assembling the Outer Chassis Rails

2.Insert the end bracket and the end rail onto the middle rail and secure them with the screws as shown.

3.Install a set of outer rail assemblies to each side of the rack and secure them with the screws provided.

4.Check that both sets of inner rails are securely attached to the chassis.

5.Check that both sets of outer rails are securely attached to the rack.

6.Insert the inner rails on the chassis, into the outer rails on the rack.

7.Gently slide the chassis into position within the rack.

5-5

Image 47
Contents Super SC743 Chassis Manual About This Manual PrefaceIntroduction Manual OrganizationTable of Contents Appendix B Power Supply Specifications Part Numbers Chapter IntroductionOverview Shipping ListWhere to get Replacement Components Asia-Pacific Contacting SupermicroHeadquarters EuropeReturning Merchandise for Service Preparing for Setup Chapter System SafetyElectrical Safety Precautions System Safety Page Chassis Power SupplyChapter Chassis Components ComponentsFront Control Panel Where to get Replacement Components Front Control PanelControl Panel LEDs Control Panel ButtonsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Side Cover of the Chassis Disconnecting the Chassis from the Power SourceRemoving the Chassis Side and Top Covers Removing the Side CoverRelease Tab Removing the Top CoverRemoving the Top Cover of the Chassis Installing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersAccessing and Removing Hard Drive Carriers Removing the Dummy Drive Installing Hard Drives into the Drive CarriersInstalling Hard Drives Installing Fixed Hard Drives in SC743i Series Chassis Models Removing the Storage Module Configuring the Storage ModuleStorage Module Options Storage Module Mobile Rack Bracket Devices Configuring the Storage Module for 5.25 DevicesRemoving and Replacing Mid-chassis Fans Removing and Replacing the System FansSC743TQ-865B-SQ Cooling System Standard Cooling Systems10 Removing Rear Chassis Fans Removing Rear Chassis FansRemoving the Air Shroud Removing the Air ShroudInstalling the Motherboard Installing the MotherboardPrior to Installing the Motherboard Motherboard Installation12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage Installing the Power Supply Power Supply465, 500, 665 and 865 Watt Power Supplies Remove Screws14 15 Removing the Interior Chassis Screws on the Power Supply16 Installing the 760 Watt Power Supply Watt Power Supply17 Accessing the Interior Backplane/Midplane Space Accessing the Interior SpaceInstalling the Driver Select Enclosure Services Device and click Next Installing the Driver Alternative ProcedureSC743 Chassis Manual Unpacking the System Chapter Rack InstallationChoosing a Setup Location General Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureInstalling the Inner Chassis Rails Installing the Chassis Rack Mounting RailsBefore Installing the Chassis Rails Middle Rail End Rail End Bracket Installing the Outer Chassis RailsMounting the Chassis into a Rack Outer Rail Assemblies Inner RailsSC743S2 Series Scsi Type Length Description Appendix a Cables, Screws Other AccessoriesOverview Cables Included with the SC743 Chassis SC743S1 Series Scsi Type LengthSC743i Series Type Length Description SC743T Series SAS/SATASC743TQ Series SATA/SCSI Front Panel to the Motherboard Extending Power CablesPower Cable Extenders Number of Pins Length DVD-ROM, CD-ROM, and Floppy Drive Chassis ScrewsPower Supply Options Appendix B Power Supply SpecificationsMFR Rated AC Voltage +5V standby +12V +3.3V 865W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V R760W Product Features Appendix C CSE-M34S/CSE-M34T Mobile Rack SpecificationsSupported Operating Systems Packing ListAdditional Information Jumper Description Setting Front Connectors and JumpersJumper Settings Page Figure C-2 Jumper Locations Jumper Settings and Locations for the CSE-M35T SataRelease Buttons Installation ProceduresInstalling the CSE-M35S Backplane Accessing Hot-Swappable DrivesFigure C-5 Installing the Drive into the Drive Tray Installing a Drive into the Drive TrayFigure C-6 Accessing the Backplane Accessing the BackplaneSC743 Chassis Manual System Monitoring Appendix D M35TQ Mobile Rack SpecificaitonsAn Important Note to the User ESD Safety GuidelinesGeneral Safety Guidelines Introduction to the SAS-M35TQ Backplane Front Connectors Figure D-1 Front Connectors5. I2C Connectors Front Connectors and Pin DefinitionsMobile Rack Main Power Connectors Jtag ConnectorActivity LED Header Upgrade ConnectorFan Connector 7. Sideband HeadersJP40 Front Jumper Locations and Pin DefinitionsBuzzer alarm is triggered by the following conditions Buzzer and Chip Reset Jumper SettingsJumper Settings Fan Jumper Settings Fan Jumper SettingsI2C Setting Default I2C and Sgpio Modes and Jumper SettingsI2C/SGPIO Settings Jumper Figure D-6 Rear Connectors and LED Indicators Rear Connectors and LED IndicatorsHard Drive Activity Rear SAS/SATA ConnectorsRear LED Indicators Drive NumberTools Required Preparing for InstallationImportant Safety Guidelines Safety GuidelinesRemoving Hard Drives from the Mobile Rack Installation ProceduresInstalling Hard Drives into the Mobile Rack Release ButtonDummy Drive Drive Carrier Installing a Hard Drive into the Hard Drive CarrierSAS/SATA or Scsi Hard Drive Drive Tray Figure D-10 Installing a Hard DriveRemoving the Exhaust Fan and Connecting SAS/SATA Cables Connecting Cables to the Mobile RackFigure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Backplane Screw Locations Additional Optional Installation InformationAppendix E SAS-743TQ Backplane Specifications Introduction to the SAS-743TQ Backplane An Important Note to UsersFigure E-1 Front Connectors Front Connectors#3. MG9072 Chip Front Connector and Pin Definitions#1. and 2. Jtag Connector and Upgrade Connectors #4. Backplane Main Power Connectors#10. #17. SAS Ports #8. and #9. I2C Connectors#6. and #7. Sideband Headers JP34 JP41Connector Pins Jumper Setting SAS Port Connections in I2C and Sgpio Settings I2C and Sgpio Mode Jumper SettingsOH/Drive Fail LED Front LED IndicatorsState Specification SAS Drive Number J15Appendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Figure F-1 Front Connectors Connectors and JumpersFront Connector and Jumper Pin Definitions JP18 MM2 Explanation of JumpersJP25 Normal State Indicator Status Front LED IndicatorFigure F-4 Rear Connectors Rear Sata Connectors Rear ConnectorsRear LEDs Appendix F SATA-743 Backplane Specifications