SUPER MICRO Computer FAN0103L4 user manual Dummy Drive Drive Carrier

Page 79

Appendix D: M35TQ Mobile Rack Specifications

Dummy Drive

Drive Carrier

Figure D-8: Chassis Drive Carrier

!

Warning: Except for short periods of time while swapping hard drives, do not operate the server with the mobile rack hard drive bays empty. The hard drive carrier must have a hard drive or dummy drive installed.

1

1

 

2

1

Figure D-9: Removing Dummy Drive from Carrier

Installing a Hard Drive into the Hard Drive Carrier

1.Remove the two screws holding securing the dummy drive to the carrier.

2.Remove the dummy drive from the carrier.

D-15

Image 79
Contents Super SC743 Chassis Manual About This Manual PrefaceIntroduction Manual OrganizationTable of Contents Appendix B Power Supply Specifications Part Numbers Chapter IntroductionOverview Shipping ListWhere to get Replacement Components Asia-Pacific Contacting SupermicroHeadquarters EuropeReturning Merchandise for Service Preparing for Setup Chapter System SafetyElectrical Safety Precautions System Safety Page Chassis Power SupplyChapter Chassis Components ComponentsFront Control Panel Where to get Replacement Components Front Control PanelControl Panel LEDs Control Panel ButtonsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Side Cover of the Chassis Disconnecting the Chassis from the Power SourceRemoving the Chassis Side and Top Covers Removing the Side CoverRemoving the Top Cover of the Chassis Removing the Top CoverRelease Tab Accessing and Removing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersInstalling Hard Drive Carriers Installing Hard Drives Installing Hard Drives into the Drive CarriersRemoving the Dummy Drive Installing Fixed Hard Drives in SC743i Series Chassis Models Storage Module Options Configuring the Storage ModuleRemoving the Storage Module Storage Module Mobile Rack Bracket Devices Configuring the Storage Module for 5.25 DevicesRemoving and Replacing Mid-chassis Fans Removing and Replacing the System FansSC743TQ-865B-SQ Cooling System Standard Cooling Systems10 Removing Rear Chassis Fans Removing Rear Chassis FansRemoving the Air Shroud Removing the Air ShroudInstalling the Motherboard Installing the MotherboardPrior to Installing the Motherboard Motherboard Installation12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage 465, 500, 665 and 865 Watt Power Supplies Power SupplyInstalling the Power Supply Remove Screws14 15 Removing the Interior Chassis Screws on the Power Supply16 Installing the 760 Watt Power Supply Watt Power Supply17 Accessing the Interior Backplane/Midplane Space Accessing the Interior SpaceInstalling the Driver Select Enclosure Services Device and click Next Installing the Driver Alternative ProcedureSC743 Chassis Manual Choosing a Setup Location Chapter Rack InstallationUnpacking the System General Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureBefore Installing the Chassis Rails Installing the Chassis Rack Mounting RailsInstalling the Inner Chassis Rails Middle Rail End Rail End Bracket Installing the Outer Chassis RailsMounting the Chassis into a Rack Outer Rail Assemblies Inner RailsSC743S2 Series Scsi Type Length Description Appendix a Cables, Screws Other AccessoriesOverview Cables Included with the SC743 Chassis SC743S1 Series Scsi Type LengthSC743TQ Series SATA/SCSI SC743T Series SAS/SATASC743i Series Type Length Description Power Cable Extenders Number of Pins Length Extending Power CablesFront Panel to the Motherboard DVD-ROM, CD-ROM, and Floppy Drive Chassis ScrewsPower Supply Options Appendix B Power Supply SpecificationsMFR Rated AC Voltage +5V standby +12V +3.3V R760W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V 865W Product Features Appendix C CSE-M34S/CSE-M34T Mobile Rack SpecificationsSupported Operating Systems Packing ListAdditional Information Jumper Settings Front Connectors and JumpersJumper Description Setting Page Figure C-2 Jumper Locations Jumper Settings and Locations for the CSE-M35T SataRelease Buttons Installation ProceduresInstalling the CSE-M35S Backplane Accessing Hot-Swappable DrivesFigure C-5 Installing the Drive into the Drive Tray Installing a Drive into the Drive TrayFigure C-6 Accessing the Backplane Accessing the BackplaneSC743 Chassis Manual System Monitoring Appendix D M35TQ Mobile Rack SpecificaitonsGeneral Safety Guidelines ESD Safety GuidelinesAn Important Note to the User Introduction to the SAS-M35TQ Backplane Front Connectors Figure D-1 Front Connectors5. I2C Connectors Front Connectors and Pin DefinitionsMobile Rack Main Power Connectors Jtag ConnectorActivity LED Header Upgrade ConnectorFan Connector 7. Sideband HeadersJP40 Front Jumper Locations and Pin DefinitionsJumper Settings Buzzer and Chip Reset Jumper SettingsBuzzer alarm is triggered by the following conditions Fan Jumper Settings Fan Jumper SettingsI2C/SGPIO Settings Jumper I2C and Sgpio Modes and Jumper SettingsI2C Setting Default Figure D-6 Rear Connectors and LED Indicators Rear Connectors and LED IndicatorsHard Drive Activity Rear SAS/SATA ConnectorsRear LED Indicators Drive NumberTools Required Preparing for InstallationImportant Safety Guidelines Safety GuidelinesRemoving Hard Drives from the Mobile Rack Installation ProceduresInstalling Hard Drives into the Mobile Rack Release ButtonDummy Drive Drive Carrier Installing a Hard Drive into the Hard Drive CarrierSAS/SATA or Scsi Hard Drive Drive Tray Figure D-10 Installing a Hard DriveRemoving the Exhaust Fan and Connecting SAS/SATA Cables Connecting Cables to the Mobile RackFigure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Backplane Screw Locations Additional Optional Installation InformationAppendix E SAS-743TQ Backplane Specifications Introduction to the SAS-743TQ Backplane An Important Note to UsersFigure E-1 Front Connectors Front Connectors#3. MG9072 Chip Front Connector and Pin Definitions#1. and 2. Jtag Connector and Upgrade Connectors #4. Backplane Main Power Connectors#6. and #7. Sideband Headers #8. and #9. I2C Connectors#10. #17. SAS Ports JP34 JP41Connector Pins Jumper Setting SAS Port Connections in I2C and Sgpio Settings I2C and Sgpio Mode Jumper SettingsState Specification Front LED IndicatorsOH/Drive Fail LED SAS Drive Number J15Appendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Figure F-1 Front Connectors Connectors and JumpersFront Connector and Jumper Pin Definitions JP25 Explanation of JumpersJP18 MM2 Normal State Indicator Status Front LED IndicatorFigure F-4 Rear Connectors Rear Sata Connectors Rear ConnectorsRear LEDs Appendix F SATA-743 Backplane Specifications