SUPER MICRO Computer FAN0103L4 user manual Installing the 760 Watt Power Supply

Page 38

SC743 Chassis Manual

760 Watt Power Supply

The 760 Watt power supply is a triple redundant power supply with a different con- figuration than that of the 465, 500, 665 and 865 Watt power supplies.

Installing the Power Supply

1.Unplug the AC power cord from the power supply.

2.Push the release tab on the left side of each power supply to release it from the locked position.

3.Once released from the locked position, pull the power supply outward, using the handle provided.

4.Install the replacement power supply in the chassis.

5.Replace any other components in the chassis that have been removed and replace the chassis cover before replacing the power cord and powering up the system.

Upper Release Tab

Upper Power Cord

Middle Release Tab

Middle Power Cord

Lower Release Tab

Lower Power Cord

Figure 4-16: Installing the 760 Watt Power Supply

4-18

Image 38

Contents Super SC743 Chassis Manual Preface About This ManualManual Organization IntroductionTable of Contents Appendix B Power Supply Specifications Shipping List Chapter IntroductionOverview Part NumbersWhere to get Replacement Components Europe Contacting SupermicroHeadquarters Asia-PacificReturning Merchandise for Service Chapter System Safety Preparing for SetupElectrical Safety Precautions System Safety Page Components Power SupplyChapter Chassis Components ChassisWhere to get Replacement Components Front Control Panel Front Control PanelControl Panel Buttons Control Panel LEDsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Side Cover Disconnecting the Chassis from the Power SourceRemoving the Chassis Side and Top Covers Removing the Side Cover of the ChassisRelease Tab Removing the Top CoverRemoving the Top Cover of the Chassis Installing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersAccessing and Removing Hard Drive Carriers Removing the Dummy Drive Installing Hard Drives into the Drive CarriersInstalling Hard Drives Installing Fixed Hard Drives in SC743i Series Chassis Models Removing the Storage Module Configuring the Storage ModuleStorage Module Options Configuring the Storage Module for 5.25 Devices Storage Module Mobile Rack Bracket DevicesStandard Cooling Systems Removing and Replacing the System FansSC743TQ-865B-SQ Cooling System Removing and Replacing Mid-chassis FansRemoving Rear Chassis Fans 10 Removing Rear Chassis FansRemoving the Air Shroud Removing the Air ShroudMotherboard Installation Installing the MotherboardPrior to Installing the Motherboard Installing the Motherboard12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage Installing the Power Supply Power Supply465, 500, 665 and 865 Watt Power Supplies 15 Removing the Interior Chassis Screws on the Power Supply Remove Screws14Watt Power Supply 16 Installing the 760 Watt Power SupplyAccessing the Interior Space 17 Accessing the Interior Backplane/Midplane SpaceInstalling the Driver Installing the Driver Alternative Procedure Select Enclosure Services Device and click NextSC743 Chassis Manual Unpacking the System Chapter Rack InstallationChoosing a Setup Location Rack Precautions General Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the Inner Chassis Rails Installing the Chassis Rack Mounting RailsBefore Installing the Chassis Rails Installing the Outer Chassis Rails Middle Rail End Rail End BracketOuter Rail Assemblies Inner Rails Mounting the Chassis into a RackSC743S1 Series Scsi Type Length Appendix a Cables, Screws Other AccessoriesOverview Cables Included with the SC743 Chassis SC743S2 Series Scsi Type Length DescriptionSC743i Series Type Length Description SC743T Series SAS/SATASC743TQ Series SATA/SCSI Front Panel to the Motherboard Extending Power CablesPower Cable Extenders Number of Pins Length Chassis Screws DVD-ROM, CD-ROM, and Floppy DriveAppendix B Power Supply Specifications Power Supply OptionsMFR Rated AC Voltage +5V standby +12V +3.3V 865W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V R760W Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Product FeaturesPacking List Supported Operating SystemsAdditional Information Jumper Description Setting Front Connectors and JumpersJumper Settings Page Jumper Settings and Locations for the CSE-M35T Sata Figure C-2 Jumper LocationsAccessing Hot-Swappable Drives Installation ProceduresInstalling the CSE-M35S Backplane Release ButtonsInstalling a Drive into the Drive Tray Figure C-5 Installing the Drive into the Drive TrayAccessing the Backplane Figure C-6 Accessing the BackplaneSC743 Chassis Manual Appendix D M35TQ Mobile Rack Specificaitons System MonitoringAn Important Note to the User ESD Safety GuidelinesGeneral Safety Guidelines Introduction to the SAS-M35TQ Backplane Figure D-1 Front Connectors Front ConnectorsJtag Connector Front Connectors and Pin DefinitionsMobile Rack Main Power Connectors 5. I2C Connectors7. Sideband Headers Upgrade ConnectorFan Connector Activity LED HeaderFront Jumper Locations and Pin Definitions JP40Buzzer alarm is triggered by the following conditions Buzzer and Chip Reset Jumper SettingsJumper Settings Fan Jumper Settings Fan Jumper SettingsI2C Setting Default I2C and Sgpio Modes and Jumper SettingsI2C/SGPIO Settings Jumper Rear Connectors and LED Indicators Figure D-6 Rear Connectors and LED IndicatorsDrive Number Rear SAS/SATA ConnectorsRear LED Indicators Hard Drive ActivitySafety Guidelines Preparing for InstallationImportant Safety Guidelines Tools RequiredRelease Button Installation ProceduresInstalling Hard Drives into the Mobile Rack Removing Hard Drives from the Mobile RackInstalling a Hard Drive into the Hard Drive Carrier Dummy Drive Drive CarrierFigure D-10 Installing a Hard Drive SAS/SATA or Scsi Hard Drive Drive TrayConnecting Cables to the Mobile Rack Removing the Exhaust Fan and Connecting SAS/SATA CablesFigure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Additional Optional Installation Information Backplane Screw LocationsAppendix E SAS-743TQ Backplane Specifications An Important Note to Users Introduction to the SAS-743TQ BackplaneFront Connectors Figure E-1 Front Connectors#4. Backplane Main Power Connectors Front Connector and Pin Definitions#1. and 2. Jtag Connector and Upgrade Connectors #3. MG9072 Chip#10. #17. SAS Ports #8. and #9. I2C Connectors#6. and #7. Sideband Headers JP41 JP34Connector Pins Jumper Setting I2C and Sgpio Mode Jumper Settings SAS Port Connections in I2C and Sgpio SettingsOH/Drive Fail LED Front LED IndicatorsState Specification J15 SAS Drive NumberAppendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Connectors and Jumpers Figure F-1 Front ConnectorsFront Connector and Jumper Pin Definitions JP18 MM2 Explanation of JumpersJP25 Front LED Indicator Normal State Indicator StatusRear Connectors Figure F-4 Rear Connectors Rear Sata ConnectorsRear LEDs Appendix F SATA-743 Backplane Specifications