SUPER MICRO Computer Essential Guide for FAN0103L4 Computer Hardware Setup

Page 72

SC743 Chassis Manual

S UPER R SASM35TQ 1 REV 1.0

JP29

JP18

Figure D-3: Buzzer and Chip Reset Jumpers

Buzzer and Chip Reset Jumper Settings

Jumper Settings

Jumper

JP18

JP29

Jumper Settings

Open: Enabled

Closed: Disabled

Open: Default

Closed: Reset

Note

Buzzer Reset*

MG9072 Chip Reset

*The buzzer sound indicates that a condition requiring immediate attention has occurred.

The buzzer alarm is triggered by the following conditions:

1.Hard drive failure

2.Fan failure

3.System temperature over 45º Celsius.

D-8

Image 72

Contents Super SC743 Chassis Manual Preface About This ManualManual Organization IntroductionTable of Contents Appendix B Power Supply Specifications Chapter Introduction OverviewShipping List Part NumbersWhere to get Replacement Components Contacting Supermicro HeadquartersEurope Asia-PacificReturning Merchandise for Service Chapter System Safety Preparing for SetupElectrical Safety Precautions System Safety Page Power Supply Chapter Chassis ComponentsComponents ChassisWhere to get Replacement Components Front Control Panel Front Control PanelControl Panel Buttons Control Panel LEDsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Disconnecting the Chassis from the Power Source Removing the Chassis Side and Top CoversRemoving the Side Cover Removing the Side Cover of the ChassisRemoving the Top Cover Removing the Top Cover of the ChassisRelease Tab Accessing the Hot-Swappable Drive Carriers Accessing and Removing Hard Drive CarriersInstalling Hard Drive Carriers Installing Hard Drives into the Drive Carriers Installing Hard DrivesRemoving the Dummy Drive Installing Fixed Hard Drives in SC743i Series Chassis Models Configuring the Storage Module Storage Module OptionsRemoving the Storage Module Configuring the Storage Module for 5.25 Devices Storage Module Mobile Rack Bracket DevicesRemoving and Replacing the System Fans SC743TQ-865B-SQ Cooling SystemStandard Cooling Systems Removing and Replacing Mid-chassis FansRemoving Rear Chassis Fans 10 Removing Rear Chassis FansRemoving the Air Shroud Removing the Air ShroudInstalling the Motherboard Prior to Installing the MotherboardMotherboard Installation Installing the Motherboard12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage Power Supply 465, 500, 665 and 865 Watt Power SuppliesInstalling the Power Supply 15 Removing the Interior Chassis Screws on the Power Supply Remove Screws14Watt Power Supply 16 Installing the 760 Watt Power SupplyAccessing the Interior Space 17 Accessing the Interior Backplane/Midplane SpaceInstalling the Driver Installing the Driver Alternative Procedure Select Enclosure Services Device and click NextSC743 Chassis Manual Chapter Rack Installation Choosing a Setup LocationUnpacking the System Rack Precautions General Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the Chassis Rack Mounting Rails Before Installing the Chassis RailsInstalling the Inner Chassis Rails Installing the Outer Chassis Rails Middle Rail End Rail End BracketOuter Rail Assemblies Inner Rails Mounting the Chassis into a RackAppendix a Cables, Screws Other Accessories Overview Cables Included with the SC743 ChassisSC743S1 Series Scsi Type Length SC743S2 Series Scsi Type Length DescriptionSC743T Series SAS/SATA SC743TQ Series SATA/SCSISC743i Series Type Length Description Extending Power Cables Power Cable Extenders Number of Pins LengthFront Panel to the Motherboard Chassis Screws DVD-ROM, CD-ROM, and Floppy DriveAppendix B Power Supply Specifications Power Supply OptionsMFR Rated AC Voltage +5V standby +12V +3.3V 665W MFR Rated AC Voltage +5V standby +12V +3.3V R760WMFR Rated AC Voltage +5V standby +12V +3.3V 865W Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Product FeaturesPacking List Supported Operating SystemsAdditional Information Front Connectors and Jumpers Jumper SettingsJumper Description Setting Page Jumper Settings and Locations for the CSE-M35T Sata Figure C-2 Jumper LocationsInstallation Procedures Installing the CSE-M35S BackplaneAccessing Hot-Swappable Drives Release ButtonsInstalling a Drive into the Drive Tray Figure C-5 Installing the Drive into the Drive TrayAccessing the Backplane Figure C-6 Accessing the BackplaneSC743 Chassis Manual Appendix D M35TQ Mobile Rack Specificaitons System MonitoringESD Safety Guidelines General Safety GuidelinesAn Important Note to the User Introduction to the SAS-M35TQ Backplane Figure D-1 Front Connectors Front ConnectorsFront Connectors and Pin Definitions Mobile Rack Main Power ConnectorsJtag Connector 5. I2C ConnectorsUpgrade Connector Fan Connector7. Sideband Headers Activity LED HeaderFront Jumper Locations and Pin Definitions JP40Buzzer and Chip Reset Jumper Settings Jumper SettingsBuzzer alarm is triggered by the following conditions Fan Jumper Settings Fan Jumper SettingsI2C and Sgpio Modes and Jumper Settings I2C/SGPIO Settings JumperI2C Setting Default Rear Connectors and LED Indicators Figure D-6 Rear Connectors and LED IndicatorsRear SAS/SATA Connectors Rear LED IndicatorsDrive Number Hard Drive ActivityPreparing for Installation Important Safety GuidelinesSafety Guidelines Tools RequiredInstallation Procedures Installing Hard Drives into the Mobile RackRelease Button Removing Hard Drives from the Mobile RackInstalling a Hard Drive into the Hard Drive Carrier Dummy Drive Drive CarrierFigure D-10 Installing a Hard Drive SAS/SATA or Scsi Hard Drive Drive TrayConnecting Cables to the Mobile Rack Removing the Exhaust Fan and Connecting SAS/SATA CablesFigure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Additional Optional Installation Information Backplane Screw LocationsAppendix E SAS-743TQ Backplane Specifications An Important Note to Users Introduction to the SAS-743TQ BackplaneFront Connectors Figure E-1 Front ConnectorsFront Connector and Pin Definitions #1. and 2. Jtag Connector and Upgrade Connectors#4. Backplane Main Power Connectors #3. MG9072 Chip#8. and #9. I2C Connectors #6. and #7. Sideband Headers#10. #17. SAS Ports JP41 JP34Connector Pins Jumper Setting I2C and Sgpio Mode Jumper Settings SAS Port Connections in I2C and Sgpio SettingsFront LED Indicators State SpecificationOH/Drive Fail LED J15 SAS Drive NumberAppendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Connectors and Jumpers Figure F-1 Front ConnectorsFront Connector and Jumper Pin Definitions Explanation of Jumpers JP25JP18 MM2 Front LED Indicator Normal State Indicator StatusRear Connectors Figure F-4 Rear Connectors Rear Sata ConnectorsRear LEDs Appendix F SATA-743 Backplane Specifications