SUPER MICRO Computer 6026TT-GIBXRF, 6026TT-GIBQRF, 6026TT-GTRF user manual

Page 104

SUPERSERVER 6026TT-GTRF/GIBXRF/GIBQRF User's Manual

(continued from front)

The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com- munication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro dis- claims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

C-4

Image 104
Contents Super Manual Revision Release Date November 16 Manual Organization PrefaceAbout This Manual System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Appendix a Bios Error Beep Codes Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsOther Features Onboard Controllers/PortsGraphics Controller InfiniBandIntel 5520 Chipset System Block Diagram Server Chassis Features 2U Twin System Notes GPU SubsystemNodes Sata Backplane/DrivesContacting Supermicro HeadquartersEurope Asia-PacificPage Unpacking the System Chapter Server InstallationPreparing for Setup Choosing a Setup Location Ambient Operating Temperature Rack Mounting ConsiderationsRemoving the Protective Film Removing the Protective FilmRail Assembly Rack Mounting InstructionsSeparating the Sections of the Rack Rails Separating the Inner and Outer RailsInstalling the Inner Rail Extensions Installing the Inner RailsInstalling the Outer Rails to the Rack Outer Rack RailsInstalling Into the Rack Installing the Chassis into a RackChecking the Components and Setup Checking the Serverboard SetupAccessing the Inside of a Node Figure Preparing to Power On Providing PowerChecking the Sata drives Checking the AirflowRemoving a Node from the System Page Control Panel Buttons PowerChapter System Interface Overheat/Fan Fail Control Panel LEDsSata Drive Carrier LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup Handling the ServerboardI/O Ports I/O PortsProcessor and Heatsink Installation Installing LGA1366 ProcessorsCPU Installing a CPU Heatsink Removing the Heatsink Memory Support Installing MemoryInstalling Memory Modules Dimm Installation Notch Front ViewPCI Express Slot PCI Card InstallationAdding PCI Cards Serverboard Details LE2Jumper Description Connector DescriptionServerboard Quick Reference Connector Definitions Front Panel Accessible Add-on Card Header JF2NMI Header Internal BuzzerUniversal Serial Bus USB Video ConnectorFan Header Ethernet Ports InfiniBand Connection X8DTT-HIBXF+/ HIBQF+Serial Ports System ResetUnit Identifier Switches To Clear Cmos Jumper SettingsCmos Clear VGA Enable/Disable LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable Onboard Indicators InfiniBand LED Indicators LEB1/LEB2Onboard Power LED LAN1/LAN2 LEDsSerial ATA Ports BMC Activity LED LE2Rear UID LED LE4 Serial ATA ConnectionsInstalling Additional Drivers 12 Configuring Supero Doctor Page Chapter Advanced Chassis Setup Control Panel System FansChanging a System Fan Fan ConfigurationSystem Fan Failure Hard Drive Installation/Removal Installing and Removing Hard DrivesInstalling a Hard Drive into the Drive Carrier OverviewInstalling/Removing Hot-swap Drives Removing a Dummy Drive TrayNode a Node B Node Installation/Removal Removing a NodeRemoving a System Node Installing the Air Shrouds Power SupplyInstalling an Air Shroud Removing/Replacing the Power Supply FigureRemoving the Power Supply Release Tab Starting Bios Setup Utility How To Change the Configuration DataChapter IntroductionMain Setup Starting the Setup UtilitySystem Overview System Time/System DateBios Build Date AMI Bios Core VersionProcessor CPU TypeAdvanced Setup Configurations Xboot FeaturesXPower Configuration XProcessor and Clock OptionsHardware Prefetcher Available when supported by the CPU C1E SupportActive Processor Cores Intel Eist TechnologyXAdvanced Chipset Control Xcpu Bridge ConfigurationMemory Mode Memory ECC Error ThresholdQPI L0s and L1 Memory FrequencyHysteresis Temperature Guardband TemperatureInlet Temperature Temperature RiseXNorth Bridge Configuration XSouthBridge ConfigurationXIDE/SATA Configuration LBA/Large Mode PIO ModeSATA#2 Configuration TypeDMA Mode XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationSredir Memory Display Delay CPU Overheat AlarmXHardware Health Monitor Terminal TypeCPU Temperature/System Temperature CPU TemperatureAcpi Version Features Acpi Apic Support Xacpi ConfigurationFan Speed Control Monitor Fan1 ~ Fan 4 ReadingXGeneral Whea Configuration Xipmi Configuration X8DTT-HF/-HIBXF/-HIBQF OnlyXView BMC System Event Log XSet LAN ConfigurationXIP Address Configuration Parameter SelectorXmac Address Configuration XSubnet Mask ConfigurationXGateway Address Configuration Subnet MaskCurrent Subnet Mask in BMC Gateway AddressSecurity Settings Xdmi Event LogBoot Configuration XBoot Device PriorityPassword Check Boot Sector Virus ProtectionXCD/DVD Drives XHard Disk DrivesXRemovable Drives Bios Recovery Exit OptionsHow to Recover the Amibios Image the Main Bios Block Boot Sector Recovery from a USB DeviceBoot Sector Recovery from a Serial Port Serial Flash How to use Serial Flash for Boot Sector RecoveryPage Page Bios Error Beep Codes Appendix a Bios Error Beep CodesBios Error Beep Codes Page Appendix B Installing Windows Installing Windows for a RAID SystemInstalling Windows for a Non-RAID System Bios Appendix C System SpecificationsChassis Regulatory Compliance