SUPER MICRO Computer 6026TT-GIBXRF, 6026TT-GIBQRF, 6026TT-GTRF user manual

Page 95

Chapter 7: BIOS

4. Power on your system and click the <Connect> button in the Hyper Terminal.

The terminal screen will display the following messages.

5.Following the instructions given on the screen to update the BIOS. These instructions are also shown below.

a. At the prompt, press the <SpaceBar> to update the BIOS.

b.When asked to conﬁrm BIOS updating, press <y> to conﬁrm BIOS updates.

c.Press <y> again to begin ﬂashing BIOS remotely.

Note: Be sure to complete Steps a~c above quickly because you have a second or less to do so.

7-29

Image 95

Contents Super Manual Revision Release Date November 16 Manual Organization PrefaceAbout This Manual Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents System Interface Appendix a Bios Error Beep Codes Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAInﬁniBand Other FeaturesOnboard Controllers/Ports Graphics ControllerIntel 5520 Chipset System Block Diagram Server Chassis Features Sata Backplane/Drives 2U Twin System NotesGPU Subsystem NodesAsia-Paciﬁc Contacting SupermicroHeadquarters EuropePage Unpacking the System Chapter Server InstallationPreparing for Setup Choosing a Setup Location Rack Mounting Considerations Ambient Operating TemperatureRemoving the Protective Film Removing the Protective FilmSeparating the Inner and Outer Rails Rail AssemblyRack Mounting Instructions Separating the Sections of the Rack RailsInstalling the Inner Rails Installing the Inner Rail ExtensionsOuter Rack Rails Installing the Outer Rails to the RackInstalling the Chassis into a Rack Installing Into the RackChecking the Components and Setup Checking the Serverboard SetupAccessing the Inside of a Node Figure Checking the Airﬂow Preparing to Power OnProviding Power Checking the Sata drivesRemoving a Node from the System Page Control Panel Buttons PowerChapter System Interface Overheat/Fan Fail Control Panel LEDsSata Drive Carrier LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsHandling the Serverboard Chapter Advanced Serverboard SetupI/O Ports I/O PortsInstalling LGA1366 Processors Processor and Heatsink InstallationCPU Installing a CPU Heatsink Removing the Heatsink Memory Support Installing MemoryInstalling Memory Modules Front View Dimm Installation NotchPCI Express Slot PCI Card InstallationAdding PCI Cards LE2 Serverboard DetailsJumper Description Connector DescriptionServerboard Quick Reference Internal Buzzer Connector DeﬁnitionsFront Panel Accessible Add-on Card Header JF2 NMI HeaderUniversal Serial Bus USB Video ConnectorFan Header InﬁniBand Connection X8DTT-HIBXF+/ HIBQF+ Ethernet PortsSerial Ports System ResetUnit Identiﬁer Switches To Clear Cmos Jumper SettingsCmos Clear VGA Enable/Disable LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable LAN1/LAN2 LEDs Onboard IndicatorsInﬁniBand LED Indicators LEB1/LEB2 Onboard Power LEDSerial ATA Connections Serial ATA PortsBMC Activity LED LE2 Rear UID LED LE4Installing Additional Drivers 12 Conﬁguring Supero Doctor Page Chapter Advanced Chassis Setup System Fans Control PanelChanging a System Fan Fan ConﬁgurationSystem Fan Failure Overview Hard Drive Installation/RemovalInstalling and Removing Hard Drives Installing a Hard Drive into the Drive CarrierRemoving a Dummy Drive Tray Installing/Removing Hot-swap DrivesNode a Node B Removing a Node Node Installation/RemovalRemoving a System Node Removing/Replacing the Power Supply Figure Installing the Air ShroudsPower Supply Installing an Air ShroudRemoving the Power Supply Release Tab Introduction Starting Bios Setup UtilityHow To Change the Conﬁguration Data ChapterSystem Time/System Date Main SetupStarting the Setup Utility System OverviewCPU Type Bios Build DateAMI Bios Core Version ProcessorXboot Features Advanced Setup ConﬁgurationsXProcessor and Clock Options XPower ConﬁgurationIntel Eist Technology Hardware Prefetcher Available when supported by the CPUC1E Support Active Processor CoresXcpu Bridge Conﬁguration XAdvanced Chipset ControlMemory Frequency Memory ModeMemory ECC Error Threshold QPI L0s and L1Temperature Rise Hysteresis TemperatureGuardband Temperature Inlet TemperatureXSouthBridge Conﬁguration XNorth Bridge ConﬁgurationXIDE/SATA Conﬁguration Type LBA/Large ModePIO Mode SATA#2 ConﬁgurationDMA Mode XPCI/PnP Conﬁguration XSuper IO Device Conﬁguration XRemote Access ConﬁgurationTerminal Type Sredir Memory Display DelayCPU Overheat Alarm XHardware Health MonitorCPU Temperature CPU Temperature/System TemperatureFan1 ~ Fan 4 Reading Acpi Version Features Acpi Apic SupportXacpi Conﬁguration Fan Speed Control MonitorXipmi Conﬁguration X8DTT-HF/-HIBXF/-HIBQF Only XGeneral Whea ConﬁgurationParameter Selector XView BMC System Event LogXSet LAN Conﬁguration XIP Address ConﬁgurationXSubnet Mask Conﬁguration Xmac Address ConﬁgurationGateway Address XGateway Address ConﬁgurationSubnet Mask Current Subnet Mask in BMCXdmi Event Log Security SettingsBoot Sector Virus Protection Boot ConﬁgurationXBoot Device Priority Password CheckXCD/DVD Drives XHard Disk DrivesXRemovable Drives Exit Options Bios RecoveryBoot Sector Recovery from a USB Device How to Recover the Amibios Image the Main Bios BlockHow to use Serial Flash for Boot Sector Recovery Boot Sector Recovery from a Serial Port Serial FlashPage Page Bios Error Beep Codes Appendix a Bios Error Beep CodesBios Error Beep Codes Page Installing Windows for a RAID System Appendix B Installing WindowsInstalling Windows for a Non-RAID System Appendix C System Speciﬁcations BiosChassis Regulatory Compliance