SUPER MICRO Computer 6026TT-GIBQRF, 6026TT-GTRF user manual Intel 5520 Chipset System Block Diagram

Page 12

SUPERSERVER 6026TT-GTRF/GIBXRF/GIBQRF User's Manual

#1		#2							#2	#1
#1		#2						#2		#1
#1		#2						#2		#1
DIMM	A	DIMM	A				D	DIMM	D	DIMM
	B		B			QPI	E		E
	B		B	PROCESSOR#0			E		E
DDR3		DDR3		PROCESSOR#0		PROCESSOR#1		DDR3		DDR3
	C		C				F		F

							Intel		45
QSFP		MT25408					82574		RJ-
QSFP		Connect-X IB
		PCI-E Gen2/DDR or QDR				IOH
		(For 36D Only)				IOH	Intel		RJ-45
						5520/5500	Intel
						36-D/24-D	82574
				PCI-E
			x16 Slot
										AT25
						ICH10R			SPI	DF321
						ICH10R
					PCI		4 SATA
					PCI
						LPC	Hotswap Connector
							Hotswap Connector
			II
			DDR		BMC/VGA		LPCIO W83527
			DDR
						RMII
				VGA CONN		RTL8201N PHY
					Dedicated LAN

Figure 1-1. Intel 5520 Chipset:

System Block Diagram

Note1: This is a general block diagram. Please see Chapter 5 for details.

Note2: The Intel 5500 (IOH-24D) chipset is available for OEM only.

1-4

Image 12

Contents Super Manual Revision Release Date November 16 Preface About This ManualManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Appendix a Bios Error Beep Codes Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsOther Features Onboard Controllers/PortsGraphics Controller InﬁniBandIntel 5520 Chipset System Block Diagram Server Chassis Features 2U Twin System Notes GPU SubsystemNodes Sata Backplane/DrivesContacting Supermicro HeadquartersEurope Asia-PaciﬁcPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Ambient Operating Temperature Rack Mounting ConsiderationsRemoving the Protective Film Removing the Protective FilmRail Assembly Rack Mounting InstructionsSeparating the Sections of the Rack Rails Separating the Inner and Outer RailsInstalling the Inner Rail Extensions Installing the Inner RailsInstalling the Outer Rails to the Rack Outer Rack RailsInstalling Into the Rack Installing the Chassis into a RackChecking the Serverboard Setup Accessing the Inside of a Node FigureChecking the Components and Setup Preparing to Power On Providing PowerChecking the Sata drives Checking the AirﬂowRemoving a Node from the System Page Power Chapter System InterfaceControl Panel Buttons Control Panel LEDs Sata Drive Carrier LEDsOverheat/Fan Fail Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup Handling the ServerboardI/O Ports I/O PortsProcessor and Heatsink Installation Installing LGA1366 ProcessorsCPU Installing a CPU Heatsink Removing the Heatsink Installing Memory Installing Memory ModulesMemory Support Dimm Installation Notch Front ViewPCI Card Installation Adding PCI CardsPCI Express Slot Serverboard Details LE2Connector Description Serverboard Quick ReferenceJumper Description Connector Deﬁnitions Front Panel Accessible Add-on Card Header JF2NMI Header Internal BuzzerVideo Connector Fan HeaderUniversal Serial Bus USB Ethernet Ports InﬁniBand Connection X8DTT-HIBXF+/ HIBQF+System Reset Unit Identiﬁer SwitchesSerial Ports Jumper Settings Cmos ClearTo Clear Cmos LAN1/LAN2 Enable/Disable Watch Dog Enable/DisableVGA Enable/Disable Onboard Indicators InﬁniBand LED Indicators LEB1/LEB2Onboard Power LED LAN1/LAN2 LEDsSerial ATA Ports BMC Activity LED LE2Rear UID LED LE4 Serial ATA ConnectionsInstalling Additional Drivers 12 Conﬁguring Supero Doctor Page Chapter Advanced Chassis Setup Control Panel System FansFan Conﬁguration System Fan FailureChanging a System Fan Hard Drive Installation/Removal Installing and Removing Hard DrivesInstalling a Hard Drive into the Drive Carrier OverviewInstalling/Removing Hot-swap Drives Removing a Dummy Drive TrayNode a Node B Node Installation/Removal Removing a NodeRemoving a System Node Installing the Air Shrouds Power SupplyInstalling an Air Shroud Removing/Replacing the Power Supply FigureRemoving the Power Supply Release Tab Starting Bios Setup Utility How To Change the Conﬁguration DataChapter IntroductionMain Setup Starting the Setup UtilitySystem Overview System Time/System DateBios Build Date AMI Bios Core VersionProcessor CPU TypeAdvanced Setup Conﬁgurations Xboot FeaturesXPower Conﬁguration XProcessor and Clock OptionsHardware Prefetcher Available when supported by the CPU C1E SupportActive Processor Cores Intel Eist TechnologyXAdvanced Chipset Control Xcpu Bridge ConﬁgurationMemory Mode Memory ECC Error ThresholdQPI L0s and L1 Memory FrequencyHysteresis Temperature Guardband TemperatureInlet Temperature Temperature RiseXNorth Bridge Conﬁguration XSouthBridge ConﬁgurationXIDE/SATA Conﬁguration LBA/Large Mode PIO ModeSATA#2 Conﬁguration TypeDMA Mode XPCI/PnP Conﬁguration XRemote Access Conﬁguration XSuper IO Device ConﬁgurationSredir Memory Display Delay CPU Overheat AlarmXHardware Health Monitor Terminal TypeCPU Temperature/System Temperature CPU TemperatureAcpi Version Features Acpi Apic Support Xacpi ConﬁgurationFan Speed Control Monitor Fan1 ~ Fan 4 ReadingXGeneral Whea Conﬁguration Xipmi Conﬁguration X8DTT-HF/-HIBXF/-HIBQF OnlyXView BMC System Event Log XSet LAN ConﬁgurationXIP Address Conﬁguration Parameter SelectorXmac Address Conﬁguration XSubnet Mask ConﬁgurationXGateway Address Conﬁguration Subnet MaskCurrent Subnet Mask in BMC Gateway AddressSecurity Settings Xdmi Event LogBoot Conﬁguration XBoot Device PriorityPassword Check Boot Sector Virus ProtectionXHard Disk Drives XRemovable DrivesXCD/DVD Drives Bios Recovery Exit OptionsHow to Recover the Amibios Image the Main Bios Block Boot Sector Recovery from a USB DeviceBoot Sector Recovery from a Serial Port Serial Flash How to use Serial Flash for Boot Sector RecoveryPage Page Appendix a Bios Error Beep Codes Bios Error Beep CodesBios Error Beep Codes Page Appendix B Installing Windows Installing Windows for a RAID SystemInstalling Windows for a Non-RAID System Bios Appendix C System SpeciﬁcationsChassis Regulatory Compliance