SUPER MICRO Computer 6026TT-GIBXRF Serial ATA Ports, BMC Activity LED LE2, Rear UID LED LE4

Page 53

Chapter 5: Advanced Serverboard Setup

BMC Activity LED (LE2)

A BMC Heartbeat LED is located at LE2 on the serverboard. When LE2 is on, BMC (Baseboard Management Controller) is active. See the table at right for more in- formation.

HDD/SATA LED (LE3)

An HDD/SATA LED is located at LE3 on the serverboard. This LED indicates the status of hard drive activitiy or SATA activity supported by the South Bridge.

Rear UID LED (LE4)

The Rear UID LED is located at LE4 on the serverboard. Refer to Section 5-7 for details.

5-10 Serial ATA Ports

Serial ATA Connections

A Front Panel Add-On Card header is located at JF2 on the serverboard. This header provide onboard SATA support. Plug an add-on card in JF2 to use SATA connections. These connections provide serial-link signal transmission, which is faster than that of the traditional Parallel ATA.

BMC Heartbeat LED

On	BMC is normal

HDD/SATA LED

(LE3)

Status Deﬁnition

	On	HDD/SATA
		Connected
	Off	No connection
	Off	No connection

5-19

Image 53

Contents Super Manual Revision Release Date November 16 Manual Organization PrefaceAbout This Manual Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents System Interface Appendix a Bios Error Beep Codes Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsOnboard Controllers/Ports Other FeaturesGraphics Controller InﬁniBandIntel 5520 Chipset System Block Diagram Server Chassis Features GPU Subsystem 2U Twin System NotesNodes Sata Backplane/DrivesHeadquarters Contacting SupermicroEurope Asia-PaciﬁcPage Unpacking the System Chapter Server InstallationPreparing for Setup Choosing a Setup Location Rack Mounting Considerations Ambient Operating TemperatureRemoving the Protective Film Removing the Protective FilmRack Mounting Instructions Rail AssemblySeparating the Sections of the Rack Rails Separating the Inner and Outer RailsInstalling the Inner Rails Installing the Inner Rail ExtensionsOuter Rack Rails Installing the Outer Rails to the RackInstalling the Chassis into a Rack Installing Into the RackChecking the Components and Setup Checking the Serverboard SetupAccessing the Inside of a Node Figure Providing Power Preparing to Power OnChecking the Sata drives Checking the AirﬂowRemoving a Node from the System Page Control Panel Buttons PowerChapter System Interface Overheat/Fan Fail Control Panel LEDsSata Drive Carrier LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsHandling the Serverboard Chapter Advanced Serverboard SetupI/O Ports I/O PortsInstalling LGA1366 Processors Processor and Heatsink InstallationCPU Installing a CPU Heatsink Removing the Heatsink Memory Support Installing MemoryInstalling Memory Modules Front View Dimm Installation NotchPCI Express Slot PCI Card InstallationAdding PCI Cards LE2 Serverboard DetailsJumper Description Connector DescriptionServerboard Quick Reference Front Panel Accessible Add-on Card Header JF2 Connector DeﬁnitionsNMI Header Internal BuzzerUniversal Serial Bus USB Video ConnectorFan Header InﬁniBand Connection X8DTT-HIBXF+/ HIBQF+ Ethernet PortsSerial Ports System ResetUnit Identiﬁer Switches To Clear Cmos Jumper SettingsCmos Clear VGA Enable/Disable LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable InﬁniBand LED Indicators LEB1/LEB2 Onboard IndicatorsOnboard Power LED LAN1/LAN2 LEDsBMC Activity LED LE2 Serial ATA PortsRear UID LED LE4 Serial ATA ConnectionsInstalling Additional Drivers 12 Conﬁguring Supero Doctor Page Chapter Advanced Chassis Setup System Fans Control PanelChanging a System Fan Fan ConﬁgurationSystem Fan Failure Installing and Removing Hard Drives Hard Drive Installation/RemovalInstalling a Hard Drive into the Drive Carrier OverviewRemoving a Dummy Drive Tray Installing/Removing Hot-swap DrivesNode a Node B Removing a Node Node Installation/RemovalRemoving a System Node Power Supply Installing the Air ShroudsInstalling an Air Shroud Removing/Replacing the Power Supply FigureRemoving the Power Supply Release Tab How To Change the Conﬁguration Data Starting Bios Setup UtilityChapter IntroductionStarting the Setup Utility Main SetupSystem Overview System Time/System DateAMI Bios Core Version Bios Build DateProcessor CPU TypeXboot Features Advanced Setup ConﬁgurationsXProcessor and Clock Options XPower ConﬁgurationC1E Support Hardware Prefetcher Available when supported by the CPUActive Processor Cores Intel Eist TechnologyXcpu Bridge Conﬁguration XAdvanced Chipset ControlMemory ECC Error Threshold Memory ModeQPI L0s and L1 Memory FrequencyGuardband Temperature Hysteresis TemperatureInlet Temperature Temperature RiseXSouthBridge Conﬁguration XNorth Bridge ConﬁgurationXIDE/SATA Conﬁguration PIO Mode LBA/Large ModeSATA#2 Conﬁguration TypeDMA Mode XPCI/PnP Conﬁguration XSuper IO Device Conﬁguration XRemote Access ConﬁgurationCPU Overheat Alarm Sredir Memory Display DelayXHardware Health Monitor Terminal TypeCPU Temperature CPU Temperature/System TemperatureXacpi Conﬁguration Acpi Version Features Acpi Apic SupportFan Speed Control Monitor Fan1 ~ Fan 4 ReadingXipmi Conﬁguration X8DTT-HF/-HIBXF/-HIBQF Only XGeneral Whea ConﬁgurationXSet LAN Conﬁguration XView BMC System Event LogXIP Address Conﬁguration Parameter SelectorXSubnet Mask Conﬁguration Xmac Address ConﬁgurationSubnet Mask XGateway Address ConﬁgurationCurrent Subnet Mask in BMC Gateway AddressXdmi Event Log Security SettingsXBoot Device Priority Boot ConﬁgurationPassword Check Boot Sector Virus ProtectionXCD/DVD Drives XHard Disk DrivesXRemovable Drives Exit Options Bios RecoveryBoot Sector Recovery from a USB Device How to Recover the Amibios Image the Main Bios BlockHow to use Serial Flash for Boot Sector Recovery Boot Sector Recovery from a Serial Port Serial FlashPage Page Bios Error Beep Codes Appendix a Bios Error Beep CodesBios Error Beep Codes Page Installing Windows for a RAID System Appendix B Installing WindowsInstalling Windows for a Non-RAID System Appendix C System Speciﬁcations BiosChassis Regulatory Compliance