Seagate ST9250315AS Shock, Operating shock, Nonoperating shock, Vibration, Operating vibration

Page 21

2.10.5Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

Note. Additional shock protection is provided by the Free Fall Protection feature on ST9500325ASG, ST9320325ASG, ST9250315ASG, ST9160314ASG, ST9120315ASG and ST980313ASG models. See Section 2.13.1 for additional information about this feature.

2.10.5.1Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.

2.10.5.2Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1,000 Gs based on a nonrepetitive half-sine shock pulse of 1 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 600 Gs based on a nonrepetitive half-sine shock pulse of 0.5 msec duration.

2.10.6Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.10.6.1Operating vibration

The maximum vibration levels that the drive may experience while meeting the performance standards speci- fied in this document are specified below.

5–500 Hz

1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.

2.10.6.2Nonoperating vibration

The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degrada- tion in performance when subsequently put into operation are specified below.

5–500 Hz:

5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.

Momentus 5400.6 SATA Product Manual, Rev. E

15

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Momentus 5400.6 Sata Page Contents Momentus 5400.6 Sata Product Manual, Rev. E List of Figures Page Introduction About the Serial ATA interface Drive specifications Specification summary tableDrive specifications for 500, 400 and 320 GB models Revision 2.6 specification See notes after Table Drive specifications for 250 and 160 GB models Drive specifications for 250 and 160 GB models Drive specifications for 120 and 80 GB models Formatted capacity Formatted Guaranteed Bytes per Model Capacity SectorsLBA mode Default logical geometryPhysical organization Recording and interface technologySeek time Physical characteristicsStart/stop times Typical seek timesPower specifications Deferred spinup Typical current profileConducted noise Voltage tolerancePower management modes Power-management modesActive mode Idle modeEnvironmental specifications Operating shock ShockNonoperating shock VibrationAcoustics Drive A-weighted Sound Power Levels SWL, BAElectromagnetic immunity Test for Prominent Discrete Tones PDTsFree Fall Protection feature Measurement type SpecificationReliability Agency certification Safety certificationElectromagnetic compatibility Korean RRLFCC verification Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS China Restriction of Hazardous Substances RoHS DirectiveHandling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveTop cover stiffness/deflection Drive mountingMeasurements shown in are in inches Signal Serial ATA connector pin definitionsSerial ATA Sata interface Segment Pin Function DefinitionP10 Ground 2nd mate P11 Reserved Pin Function DefinitionCommand name Command code in hex ATA-standard commands Supported ATA commandsATA-standard security commands Command name Command code in hexWord Description Value Identify Device commandXxxxH Description if bit is set to Bit Momentus 5400.6 Sata Product Manual, Rev. E Set Features command values Set Features command3 S.M.A.R.T. commands M.A.R.T. commandsCode in features register A.R.T. command Seagate Technology support services Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page Page Momentus 5400.6 Sata Product Manual, Rev. E Page Seagate Technology LLC
Related manuals
Manual 48 pages 57.09 Kb
Top Page Image Contents