Seagate ST9600104SS, ST9600204SS, ST9600004SS Start/stop time, General performance characteristics

Page 19

5.2.2Format command execution time for 512-byte sectors (minutes)

 

ST9600204SS

ST9450404SS

 

ST9600104SS

ST9450304SS

 

ST9600004SS

ST9450204SS

Maximum (with verify)

184

136

Maximum (without verify)

92

68

Note. There is approximately a 1.5 increase in time to format a SED drive versus a non-SED drive of the same capacity.

5.2.3General performance characteristics

Minimum sector interleave

1 to 1

Data buffer to/from disc media (one 512-byte logical block)*

72 to 135 MB/s

Sustained transfer rate

72 to 135 MB/s

SAS Interface maximum instantaneous transfer rate

600 MB/s* per port

 

(dual port = 1200 MB/s*)

Logical block sizes

 

512 (default), 520, 524 or 528.

 

Read/write consecutive sectors on a track

Yes

Flaw reallocation performance impact (for flaws reallocated at format time using the

Negligible

spare sectors per sparing zone reallocation scheme.)

 

Average rotational latency

3.0ms

*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or from the host.

5.3Start/stop time

The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied.

If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 30 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT command.

The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 20 sec- onds (maximum) from removal of DC power. SCSI stop time is 20 seconds. There is no power control switch on the drive.

Savvio 10K.4 SAS Product Manual, Rev. E

11

Page 18 Page 20
Image 19
Page 18 Page 20
Contents SED Fips 140-2 Models ST9600204SSST9600104SS ST9450404SSST9450304SSST9600004SS ST9450204SS Standard Models Self-Encrypting Drive ModelsRevision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Savvio 10K.4 SAS Product Manual, Rev. E List of Figures Page Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlCaching write data Prefetch operation Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bShipping Product warrantyProduct repair and return information PowerChoiceTM power management Physical/electrical specificationsPowerChoice modes DC power requirements AC power requirementsPage 450GB standard model DC power requirements 0Gb mode Amps Power sequencing General DC power requirement notesConducted noise immunity Current profiles for 600GB models Current profilesCurrent profiles for 450GB models GB models in 3Gb operation Power dissipation600GB models in 6Gb operation 450GB models in 3Gb operation Environmental limits Temperature a. Operating450GB models in 6Gb operation Effective altitude sea level a. Operating Relative humidityShock and vibration Shock Recommended mounting Vibration a. Operating-normal Air cleanlinessCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsPurpose About FipsLevel 2 security Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingCryptographic erase Authenticated firmware downloadPower requirements Supported commandsDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Levels of PI Setting and determining the current Type LevelIdle Read After Write Protection Information PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Inquiry data Mode Sense dataSavvio inquiry data Page Mode Pages Mode Sense data for 600GB drivesMode Sense values for 450GB drives Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification complianceLED drive signal Differential signalsNumerics IndexKCC Msid Mtbf See also cooling Page Savvio 10K.4 SAS Product Manual, Rev. E Page Seagate Technology LLC
Related manuals
Manual 82 pages 32.11 Kb
Top Page Image Contents