Seagate ST9600204SS, ST9600104SS, ST9600004SS manual AC power requirements, DC power requirements

Page 30

7.1.1PowerChoice reporting methods

PowerChoiceTM provides these reporting methods for tracking purposes:

Request Sense command reports

•Current power condition

•Method of entry

Note. Processing the Request Sense command does not impact the drive’s power save state.

Mode Sense command reports (mode page 0x1A)

•Idle conditions enabled / disabled

•Idle condition timer values (100ms increments) (default, saved, current, changeable)

Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)

•Supported power conditions

•Typical recovery time from power conditions (1ms increments)

Start/Stop Cycle Counter Log Page reports (log page 0x0E)

• Specified and accumulated Start/Stops and Load/Unload cycles

Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)

• Accumulated transitions to Active, Idle_A, Idle_B, Idle_C, Standby_Y, Standby_Z

7.2AC power requirements

None.

7.3DC power requirements

The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector.

The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply.

22	Savvio 10K.4 SAS Product Manual, Rev. E

Image 30

Contents Standard Models Self-Encrypting Drive Models ST9600204SSST9600104SS ST9450404SSST9450304SSST9600004SS ST9450204SS SED Fips 140-2 ModelsRevision history Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPage Savvio 10K.4 SAS Product Manual, Rev. E List of Figures Page Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionFormatted capacities PerformanceReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct warranty ShippingProduct repair and return information Physical/electrical specifications PowerChoiceTM power managementPowerChoice modes AC power requirements DC power requirementsPage 450GB standard model DC power requirements 0Gb mode Amps General DC power requirement notes Power sequencingConducted noise immunity Current profiles Current profiles for 600GB modelsCurrent profiles for 450GB models Power dissipation GB models in 3Gb operation600GB models in 6Gb operation 450GB models in 3Gb operation Temperature a. Operating Environmental limits450GB models in 6Gb operation Relative humidity Effective altitude sea level a. OperatingShock and vibration Shock Recommended mounting Air cleanliness Vibration a. Operating-normalCorrosive environment Acoustics Mechanical specifications Mounting configuration dimensionsAbout Fips PurposeLevel 2 security About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Protection Information PI Setting and determining the current Type LevelIdle Read After Write Levels of PIIdentifying a Protection Information drive Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Mode Sense data Inquiry dataSavvio inquiry data Page Mode Sense data for 600GB drives Mode PagesMode Sense values for 450GB drives Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification complianceLED drive signal General interface characteristicsIndex NumericsKCC Msid Mtbf See also cooling Page Savvio 10K.4 SAS Product Manual, Rev. E Page Seagate Technology LLC

Related manuals

Manual 82 pages 32.11 Kb