Seagate ST9450304SS, ST9600204SS General DC power requirement notes, Conducted noise immunity

Page 33

General DC power requirement notes.

1.Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown.

2.The +5V and +12V supplies should employ separate ground returns.

3.Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device.

4.Parameters, other than spindle start, are measured after a 10-minute warm up.

5.No terminator power.

7.3.1Conducted noise immunity

Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.

+5v	=	250 mV pp from 100 Hz to 20 MHz.
+12v	=	800 mV pp from 100 Hz to 8 KHz.
		450 mV pp from 8 KHz to 20 KHz.
		250 mV pp from 20 KHz to 5 MHz.

7.3.2Power sequencing

The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.

Savvio 10K.4 SAS Product Manual, Rev. E

25

Image 33

Contents ST9600004SS ST9450204SS ST9600204SSST9600104SS ST9450404SSST9450304SSStandard Models Self-Encrypting Drive Models SED Fips 140-2 ModelsRevision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPage Savvio 10K.4 SAS Product Manual, Rev. E List of Figures Page Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsPrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Error rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesProduct warranty ShippingProduct repair and return information Physical/electrical specifications PowerChoiceTM power managementPowerChoice modes DC power requirements AC power requirementsPage 450GB standard model DC power requirements 0Gb mode Amps General DC power requirement notes Power sequencingConducted noise immunity Current profiles for 600GB models Current profilesCurrent profiles for 450GB models GB models in 3Gb operation Power dissipation600GB models in 6Gb operation 450GB models in 3Gb operation Temperature a. Operating Environmental limits450GB models in 6Gb operation Relative humidity Effective altitude sea level a. OperatingShock and vibration Shock Recommended mounting Air cleanliness Vibration a. Operating-normalCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsAbout Fips PurposeLevel 2 security Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Idle Read After Write Setting and determining the current Type LevelProtection Information PI Levels of PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Mode Sense data Inquiry dataSavvio inquiry data Page Mode Pages Mode Sense data for 600GB drivesMode Sense values for 450GB drives Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification complianceDifferential signals General interface characteristicsNumerics IndexKCC Msid Mtbf See also cooling Page Savvio 10K.4 SAS Product Manual, Rev. E Page Seagate Technology LLC

Related manuals

Manual 82 pages 32.11 Kb