Seagate ST91000640SS, 100620418 Environmental limits, Temperature a. Operating, Relative humidity

Page 41

7.5Environmental limits

Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C).

7.5.1Temperature a. Operating

The drive meets the operating specifications over a 41°F to 140°F (5°C to 60°C) drive case temperature range with a maximum temperature gradient of 36°F (20°C) per hour.

The maximum allowable drive case temperature is 60°C. See Figure 7 for HDA case temperature measure- ment location

The MTBF specification for the drive assumes the operating environment is designed to maintain nominal case temperature. The rated MTBF is based upon a sustained case temperature of 104°F (40°C). Occa- sional excursions in operating temperature between the rated MTBF temperature and the maximum drive operating case temperature may occur without impact to the rated MTBF temperature. However continual or sustained operation at case temperatures beyond the rated MTBF temperature will degrade the drive MTBF and reduce product reliability.

Air flow may be required to achieve consistent nominal case temperature values (see Section 11.2). To con- firm that the required cooling is provided for the electronics and HDA, place the drive in its final mechanical configuration, and perform random write/read operations. After the temperatures stabilize, measure the case temperature of the drive.

b.Non-operating

–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive.

HDA Temp.

Check Point

Figure 7. Location of the HDA temperature check point

Note. Image is for reference only, may not represent actual drive.

7.5.2Relative humidity

The values below assume that no condensation on the drive occurs.

a.Operating

5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.

b.Non-operating

5% to 95% non-condensing relative humidity.

Constellation.2 SAS Product Manual, Rev. H

33

Page 40 Page 42
Image 41
Page 40 Page 42
Contents ST91000642SS ST9500622SS ST91000640SSST91000641SS ST9500620SSST9500621SSStandard Models Self-Encrypting Drive Models SED Fips 140-2 ModelsRevision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPage Constellation.2 SAS Product Manual, Rev. H List of Figures Constellation.2 SAS Product Manual, Rev. H Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesShipping Product warrantyStorage Product repair and return informationPowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirements1000GB drive Standard & SED model DC power requirements 500GB drive Standard & SED model DC power requirements Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profilesGB model current profiles 1TB model drive in 3Gb operation Power dissipation1TB model drive in 6Gb operation 500GB model drive in 3Gb operation 500GB model drive in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentSee Section Constellation.2 SAS Product Manual, Rev. H Mounting configuration dimensions Mechanical specificationsPurpose About FipsValidation Program Seagate Enterprise SEDExample of Fips tamper evidence labels Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Authenticated firmware downloadDrive locking Data bandsSupported commands Power requirementsDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Setting and determining the current Type LevelProtection Information PI Levels of PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation.2 inquiry data Mode Sense dataInquiry data Page Block Descriptor 00 00 00 00 3a 38 60 30 00 00 00 00 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification ComplianceDifferential signals General interface characteristicsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation.2 SAS Product Manual, Rev. H Page Americas Seagate Technology LLC
Top Page Image Contents