Seagate ST91000641SS Signal characteristics, SAS transmitters and receivers, Power, Ready LED Out

Page 75

12.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 16. The receiver is AC cou- pling to eliminate ground shift noise.

		TX
	T	l
	T	T M
		T M
		100
		T

Figure 16. SAS transmitters and receivers

01

01

X

100

12.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

12.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 13 for signal type and signal name information.

12.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 14.

Table 14: Ready LED Out conditions

Normal command activity		LED status

Ready LED Meaning bit mode page 19h	0		1

Spun down and no activity	Off		Off

Spun down and activity (command executing)	On		On

Spun up and no activity	On		Off

Spun up and activity (command executing)	Off		On

Spinning up or down		Blinks steadily
	(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

Format in progress, each cylinder change		Toggles on/off

Constellation.2 SAS Product Manual, Rev. H

67

Image 75

Contents SED Fips 140-2 Models ST91000640SSST91000641SS ST9500620SSST9500621SSST91000642SS ST9500622SS Standard Models Self-Encrypting Drive ModelsRevision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Constellation.2 SAS Product Manual, Rev. H List of Figures Constellation.2 SAS Product Manual, Rev. H Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StoragePhysical/electrical specifications PowerChoiceTM power managementPowerChoice modes DC power requirements AC power requirements1000GB drive Standard & SED model DC power requirements 500GB drive Standard & SED model DC power requirements General DC power requirement notes Power sequencingConducted noise immunity TB model current profiles Current profilesGB model current profiles 1TB model drive in 3Gb operation Power dissipation1TB model drive in 6Gb operation 500GB model drive in 3Gb operation 500GB model drive in 6Gb operation Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. Operating Shock and vibrationShock Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal AcousticsSee Section Constellation.2 SAS Product Manual, Rev. H Mounting configuration dimensions Mechanical specificationsSeagate Enterprise SED About FipsPurpose Validation ProgramExample of Fips tamper evidence labels Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Authenticated firmware downloadRandom number generator RNG Drive lockingSupported commands Power requirementsDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Levels of PI Setting and determining the current Type LevelIdle Read After Write Protection Information PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Mode Sense data Inquiry dataConstellation.2 inquiry data Page Block Descriptor 00 00 00 00 3a 38 60 30 00 00 00 00 00 00 02 Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation.2 SAS Product Manual, Rev. H Page Americas Seagate Technology LLC