Seagate 100620418, ST9500621SS, ST9500620SS, ST9500622SS, ST91000642SS Drive mounting, Grounding

Page 59

11.3Drive mounting

Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.

The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface stiffness:

K x X = F < 15lb = 67N

where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a known force (F) is applied to the fourth point.

11.4Grounding

Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electri- cally isolating shock mounts. If it is desired for the system chassis to not be connected to the HDA/PCBA ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mount- ing the drive in the host equipment.

Increased radiated emissions may result if you do not provide the maximum surface area ground connection between system ground and drive ground. This is the system designer’s and integrator’s responsibility.

Constellation.2 SAS Product Manual, Rev. H

51

Image 59

Contents SED Fips 140-2 Models ST91000640SSST91000641SS ST9500620SSST9500621SSST91000642SS ST9500622SS Standard Models Self-Encrypting Drive ModelsRevision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Constellation.2 SAS Product Manual, Rev. H List of Figures Constellation.2 SAS Product Manual, Rev. H Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StoragePowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirements1000GB drive Standard & SED model DC power requirements 500GB drive Standard & SED model DC power requirements Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profilesGB model current profiles 1TB model drive in 3Gb operation Power dissipation1TB model drive in 6Gb operation 500GB model drive in 3Gb operation 500GB model drive in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal AcousticsSee Section Constellation.2 SAS Product Manual, Rev. H Mounting configuration dimensions Mechanical specificationsSeagate Enterprise SED About FipsPurpose Validation ProgramExample of Fips tamper evidence labels Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Authenticated firmware downloadRandom number generator RNG Drive lockingSupported commands Power requirementsDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Levels of PI Setting and determining the current Type LevelIdle Read After Write Protection Information PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation.2 inquiry data Mode Sense dataInquiry data Page Block Descriptor 00 00 00 00 3a 38 60 30 00 00 00 00 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation.2 SAS Product Manual, Rev. H Page Americas Seagate Technology LLC