Seagate ST92011A Configuring and mounting the drive, Handling and static discharge precautions

Page 23

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s exposure to ESD.

Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

Handle the drive only by its edges or frame.

The drive is fragile—handle it with care. Do not press down on the drive top cover.

Always rest the drive on a padded, antistatic surface until you mount it in the computer.

Do not touch the connector pins or the printed circuit board.

Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

3.2Jumper settings

3.2.1Master/slave configuration

Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the 4- pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see section 3.2.2.

The “Master or single drive” option is the factory default setting.

Drive is master (or single drive)

Drive is slave

Cable select

Figure 3. Jumper settings

Momentus 5400.1 Product Manual, Rev. F

17

Image 23
Contents ST94011A ST94811A ST92011A ST92811A MomentusPage Contents Momentus 5400.1 Product Manual, Rev. F List of Figures Momentus 5400.1 Product Manual, Rev. F Momentus 5400.1 disc drive IntroductionMomentus 5400.1 Product Manual, Rev. F Drive specification ST94011A ST94811A ST92011A ST92811A Drive specificationsSpecification summary SpecificationsSpecifications Physical organization Default logical geometryLBA mode Formatted capacityRecording and interface technology Physical characteristicsTechnology Specification Time to ready Typical Max Seek timeTime to ready Typical seek times msec Read WritePower specifications Voltage tolerance Typical current profileConducted noise Idle mode Power-management modesPower management modes Active modeEnvironmental specifications Vibration ShockOperating shock Nonoperating shockElectromagnetic immunity AcousticsElectromagnetic immunity Drive level acousticsAgency certification Safety certificationMeasurement type Specification ReliabilityFCC verification Korean RRLAustralian C-Tick N176 Page Master/slave configuration Configuring and mounting the driveHandling and static discharge precautions Jumper settingsCable-select option Drive mountingCable Connector Conductor Contact Signal Name ATA interface signals and connector pinsConnector signals Connector Cable Signal Name Contact ConductorCommand name Command code in hex ATA-standard commands Supported ATA commandsSupported commands ATA-standard security commands Command name Command code in hexATA-standard power-management commands Supported commands Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordFeatures register values Set Features commandCode in features register A.R.T. command 4 S.M.A.R.T. commandsSupported S.M.A.R.T. commands Momentus 5400.1 Product Manual, Rev. F Tested systems Installation considerationsCompatibility summary System CompatibilityOperating systems tested Bios versions testedTested Bios versions Operating system versions testedVendor Application Compatibility test configurationsSoftware utilities Other certificationMomentus 5400.1 Product Manual, Rev. F Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Numerics IndexPage Page Momentus 5400.1 Product Manual, Rev. F Page Seagate Technology LLC
Related manuals
Manual 2 pages 44.41 Kb