Seagate ST9100011FS, ST950011FS manual Electromagnetic immunity, Vibration, Operating vibration

Page 20

2.9.6Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.9.6.1Operating vibration

The maximum random vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. This specification does not cover connection issues that may result from testing at this level.

20–2000 Hz

16 Grms

2.9.6.2Nonoperating vibration

The maximum random nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below.

20–2000 Hz

16 Grms

2.10Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table:

Table 5:

Radio frequency environments

 

 

 

 

 

 

 

Test

 

Description

Performance level

Reference standard

 

 

 

 

 

Electrostatic

 

Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV

B

EN 61000-4-2: 95

discharge

 

 

 

 

Radiated RF

 

80 to 1000 MHz, 3 V/m,

A

EN 61000-4-3: 96

immunity

 

80% AM with 1 kHz sine

 

ENV 50204: 95

 

 

900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz

 

 

Electrical fast

± 1 kV on AC mains, ± 0.5 kV on external I/O

B

EN 61000-4-4: 95

transient

 

 

 

 

Surge immunity

± 1 kV differential, ± 2 kV common, AC mains

B

EN 61000-4-5: 95

 

 

 

 

Conducted RF

150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine

A

EN 61000-4-6: 97

immunity

 

 

 

 

Voltage dips,

 

0% open, 5 seconds

C

EN 61000-4-11: 94

interrupts

 

0% short, 5 seconds

C

 

 

 

40%, 0.10 seconds

C

 

 

 

70%, 0.01 seconds

B

 

14

Pulsar Product Manual, Rev. A

Image 20
Contents PulsarTM ST9200011FS ST9100011FS ST950011FSRevision history Revision DateContents Pulsar Product Manual, Rev. a List of Figures Page Introduction About the Serial ATA interface Specification summary tables Drive specifications summary for 200, 100 and 50 GB modelsPulsar Product Manual, Rev. a Performance, Recording and interface technology Default logical geometry for ATA based systemsFormatted capacity Physical characteristics PerformanceTime to Ready Access timeTypical access times µs Read Write Power specifications 200GB DC power requirements 100GB DC power requirements 50GB DC power requirements Voltage tolerance Typical current profilesConducted noise Environmental specifications Electromagnetic immunity VibrationOperating vibration Nonoperating vibrationReliability specifications ReliabilityAgency certification Environmental protection ChassisCorrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingCooling Air flowSerial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionCommand name Command code in hex Supported ATA commandsSupported ATA commands C6H Identify Device command Word Description ValueXxxxh Ffffh Description if bit is set to Bit Word Bit WordDevice supports Software Settings Preservation Media serial number is supported Write-Read-Verify feature set is supported Set Features command Set Features command valuesCode in features register A.R.T. command 3 S.M.A.R.T. commandsA.R.T. commands Pulsar Product Manual, Rev. a Warranty Support Direct.seagate.com Spp.seagate.com WebTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Presales SupportIndex Page Page Pulsar Product Manual, Rev. a Page Disc Drive, Scotts Valley, California 95066-4544, USA