Seagate ST950011FS Serial ATA device plug connector pin definitions, Pin Function Definition

Page 30

4.2Serial ATA device plug connector pin definitions

Table 6 summarizes the signals on the Serial ATA interface and power connectors.

Table 6:

Serial ATA connector pin definitions

 

 

 

 

Segment

Pin

Function

Definition

 

 

 

 

 

S1

Ground

2nd mate

 

 

 

 

 

S2

A+

Differential signal pair A from Phy

 

 

 

 

 

S3

A-

 

 

 

 

 

 

S4

Ground

2nd mate

 

 

 

 

 

S5

B-

Differential signal pair B from Phy

 

 

 

 

 

S6

B+

 

Signal

 

 

 

S7

Ground

2nd mate

 

 

 

 

 

 

Key and spacing separate signal and power segments

 

 

 

 

 

P1

V33

not used

 

P2

V33

not used

 

P3

V33

not used

 

P4

Ground

1st mate

 

 

 

 

 

P5

Ground

2nd mate

 

 

 

 

 

P6

Ground

2nd mate

 

 

 

 

 

P7

V5

5V power, pre-charge, 2nd mate

Power

P8

V5

5V power

 

P9

V5

5V power

 

P10

Ground

2nd mate

 

 

 

 

 

P11

Ground or LED signal

If grounded, drive ignores this signal

 

 

 

 

 

P12

Ground

1st mate.

 

 

 

 

 

P13

V12

not used

 

P14

V12

not used

 

P15

V12

not used

Notes:

1.All pins are in a single row, with a 1.27 mm (0.050”) pitch.

2.The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are:

the ground pins P4 and P12.

the pre-charge power pins and the other ground pins.

the signal pins and the rest of the power pins.

3.There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.

4.All used voltage pins (Vx) must be terminated.

24

Pulsar Product Manual, Rev. A

Image 30
Contents PulsarTM ST9200011FS ST9100011FS ST950011FSRevision history Revision DateContents Pulsar Product Manual, Rev. a List of Figures Page Introduction About the Serial ATA interface Specification summary tables Drive specifications summary for 200, 100 and 50 GB modelsPulsar Product Manual, Rev. a Default logical geometry for ATA based systems Formatted capacityPerformance, Recording and interface technology Physical characteristics PerformanceAccess time Typical access times µs Read WriteTime to Ready Power specifications 200GB DC power requirements 100GB DC power requirements 50GB DC power requirements Typical current profiles Conducted noiseVoltage tolerance Environmental specifications Operating vibration Electromagnetic immunityVibration Nonoperating vibrationReliability specifications ReliabilityAgency certification Environmental protection ChassisCorrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingCooling Air flowSerial ATA Sata interface Hot-Plug compatibilitySignal Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex C6H Identify Device command Word Description ValueXxxxh Ffffh Description if bit is set to Bit Word Bit WordDevice supports Software Settings Preservation Media serial number is supported Write-Read-Verify feature set is supported Set Features command Set Features command values3 S.M.A.R.T. commands A.R.T. commandsCode in features register A.R.T. command Pulsar Product Manual, Rev. a Warranty Support Direct.seagate.com Spp.seagate.com WebData Recovery Services Call Center Toll-free Direct dial Technical Support Warranty ServiceData Recovery Services Authorized Service Centers Presales SupportIndex Page Page Pulsar Product Manual, Rev. a Page Disc Drive, Scotts Valley, California 95066-4544, USA