Seagate ST9200011FS, ST950011FS, ST9100011FS manual Xxxxh

Page 34

Word	Description	Value

64	Advanced PIO modes supported. SATA = 0003h	0003H
65	Minimum Multiword DMA transfer cycle time per word (120ns)	0078H
66	Recommended Multiword DMA transfer cycle time (120ns)	0078H
67	Minimum PIO transfer cycle time without flow control (120ns)	0078H
68	Minimum PIO transfer cycle time with IORDY flow control (120ns)	0078H
69	Additional Features and Commands supported.	4000H
	Trim Features supported, DMA commands supported
70	Reserved	0000H
71–74	Reserved for ATAPI	0000H
75	Queue depth	001FH
76	Serial ATA Capabilities Supported	0706H
77	Reserved for Serial ATA	0000H
78	Serial ATA features supported	004CH
79	Serial ATA features enabled	0040H
80	Major version number	01FCH
81	Minor version number	0028H
82	Commands and feature sets supported	746BH
83	Commands and feature sets supported	7501H
84	Commands and feature sets supported	6193H
85	Commands and feature sets supported or enabled	7069H
86	Commands and feature sets supported or enabled	B401H
87	Commands and feature sets supported or enabled	6163H
88	Ultra DMA support and current mode (see note following this table)	207FH
89	Security erase time	0000H
90	Enhanced security erase time	0000H
91	Current APM level value	00FEH
92	Master password Identifier	0000H
93	Hardware reset result	0000H
94	Reserved	0000H
95–99	ATA-reserved	0000H
100–103	Total Number of User Addressable Logical Blocks for 48-bit com-	200GB model =	390,721,968
	mands. These words are required for drives that support the 48-bit	100GB model =	195,371,568
	addressing feature. Maximum value: 0000FFFFFFFFFFFFh	50GB model =	97,696,368
104	Reserved for Streaming Command Set	0000H
105	Maximum number of 512-byte blocks of LBA Range Entries	0001H
	(see 4.18.3.2) per DATA SET MANAGEMENT command
106	Physical sector size / logical sector size	4000H
107	Inter-seek delay for ISO 7779 standard acoustic testing	0000H
108–111	World wide name	XXXXH

28	Pulsar Product Manual, Rev. A

Image 34

Contents PulsarTM ST9200011FS ST9100011FS ST950011FSRevision history Revision DateContents Pulsar Product Manual, Rev. a List of Figures Page Introduction About the Serial ATA interface Specification summary tables Drive specifications summary for 200, 100 and 50 GB modelsPulsar Product Manual, Rev. a Formatted capacity Default logical geometry for ATA based systemsPerformance, Recording and interface technology Physical characteristics PerformanceTypical access times µs Read Write Access timeTime to Ready Power specifications 200GB DC power requirements 100GB DC power requirements 50GB DC power requirements Conducted noise Typical current profilesVoltage tolerance Environmental specifications Operating vibration Electromagnetic immunityVibration Nonoperating vibrationReliability specifications ReliabilityAgency certification Environmental protection ChassisCorrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingCooling Air flowSerial ATA Sata interface Hot-Plug compatibilitySignal Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex C6H Identify Device command Word Description ValueXxxxh Ffffh Description if bit is set to Bit Word Bit WordDevice supports Software Settings Preservation Media serial number is supported Write-Read-Verify feature set is supported Set Features command Set Features command valuesA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Pulsar Product Manual, Rev. a Warranty Support Direct.seagate.com Spp.seagate.com WebData Recovery Services Call Center Toll-free Direct dial Technical Support Warranty ServiceData Recovery Services Authorized Service Centers Presales SupportIndex Page Page Pulsar Product Manual, Rev. a Page Disc Drive, Scotts Valley, California 95066-4544, USA